manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 185 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 185

Chapter 4 Getting Started with Device Manager

185

System Configuration Guide

 

Status bar

The status bar displays error and informational messages from the software 
application. These messages are not related to the device being managed.

Using the buttons in Device Manager dialog boxes

Table 37

 describes buttons in Device Manager dialog boxes. 

Table 37   

Device Manager buttons

Button

Name

Description

Insert

Opens a dialog box to create a new entry for a table; then 
from the dialog box, inserts the new entry in the table.

Copy

Copies selected cells from a table.

Paste

Pastes copied values to a currently selected table cell.

Reset 
Changes

Causes changed (but not applied) fields to revert to their 
previous values.

Print Table or 
Print Graph

Prints the table or graph that is displayed.

Stop/Refresh

Stops the current action (compiling, saving, and so forth). 
If you are updating or compiling a large data table, the 
Refresh button changes to a Stop button while this action 
is taking place. Clicking the Stop button interrupts the 
polling process.

Export Data

Exports information to a file you specify. You can then 
import this file into a text editor or spreadsheet for further 
analysis. 

Note: 

Not all buttons appear in all the dialog boxes.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments