manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 148 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 148

148

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

 

•

“Installing JDM on Windows” on page 149

•

“Installing JDM on UNIX or Linux” on page 159

•

“Starting Device Manager” on page 171

JDM installation precautions

The following warnings apply to Device Manager on all operating environments: 

•

The JDM and Ethernet Switch software versions must match for the correct 
dialog boxes and information to be shown and accessible. Please refer to the 
Release Notes for a complete compatibility list.

•

If you want to use JDM to support multiple Nortel switches in your network, 
ensure that the JDM version you use supports each version of software 
running on each Nortel device in your network. 

•

Prior to upgrading JDM, either uninstall your previous version of the Device 
Manager software, or install the new software to a different directory. (You 
can have multiple versions of Device Manager stored on your Windows, 
UNIX, or Linux machine, provided that each version is stored in a separate 
directory.)

•

JDM saves the IP addresses that are visited to a settings file. A JDM uninstall 
operation does not remove this settings file.

— In a Windows environment, the settings file is 

dm.ini

, and is created in the 

JDM install directory.

— In a UNIX environment, the settings file is 

~/.jdm/dm.ini

.

— In a Linux environment, the settings file is 

~/.jdm/dm.ini

.

•

The 

dm.ini

 file containing IP addresses visited from a previous JDM version 

is automatically used by a new JDM version installed in the same directory. 
You must manually move or copy the 

dm.ini 

file from a previous version of 

JDM to a new JDM installation in a different directory.

Note: 

Do not install the JDM to a directory where a previous version of 

Device Manager software already exists.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments