manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 119 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 119

119

System Configuration Guide

 

Chapter 3
CLI Basics

You can manage the Ethernet Switch 325/425 with a number of management tools 
such as:

•

Device Manager (GUI)

•

Web-based management system 

•

Console Interface (CI menus)

•

Command Line Interface (CLI)

The Ethernet Switch 325/425 Command Line Interface (CLI) is a management 
tool that provides methods for configuring, managing, and monitoring the 
operational functions of the switch. You can access CLI through a direct 
connection to the switch console port, or remotely using Telnet. For a complete, 
alphabetical list of CLI commands, refer to 

Appendix E, “Command List,” on 

page 447

.

You can use the CLI interactively, or you can load and execute CLI “scripts.” CLI 
scripts are loaded in one of the following ways:

•

Entering the 

configure network

 command

•

Manually loading the script in the console menu

•

Automatically loading the script at boot-up

This chapter discusses the following CLI topics:

•

“CLI command modes”

•

“Port numbering” on page 123

•

“Accessing CLI” on page 125

•

“Setting the system username and password” on page 127

•

“Getting help” on page 128

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments