manualshive.com logo in svg

Nortek SD Ultra Low Nox Series, Installation Instructions Manual

Share
Download
Nortek SD Ultra Low Nox Series Installation Instructions Manual Download Page 1

95.0% AFUE

*SD Ultra Low Nox Series Single Stage, Condensing Gas Furnace

*SD Upflow / Horizontal Furnace

INSTALLATION INSTRUCTIONS

 WARNING

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly could result in serious injury, death or property 

damage.

•  Installation and service must be performed by a qualified installer, service agency or the gas 

supplier.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or 

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

•  Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers instructions.

• If you cannot reach your gas supplier, call the fire department.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

This product complies with SJVAPCD 4905 and SCAQMD 1111 with NOx levels below 14 ng/J when operated on natural gas.

Summary of Contents for SD Ultra Low Nox Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands