background image

INSTALLATION CHECKLIST

INSTALLATION ADDRESS:

CITY:

STATE:

UNIT MODEL #

UNIT SERIAL #

INSTALLER NAME:

CITY

STATE

Unit Installed Minimum clearances 
shown on 

page 3

?

YES

NO

Has the owner’s information been 

reviewed with the customer?

YES

NO

Has the Literature Package been 

left with the unit?

YES

NO

REFRIGERATION SYSTEM

Was unit given 24 hr warm up 

period for crankcase heaters?

YES

NO

Stage-1 Liquid Pressure (high side):

Stage-1 Suction Pressure (low side):

REPLACEMENT PARTS

Replacement parts are available through your distributor. 

Please have the complete model and serial number of the 

unit when ordering replacement parts.

ELECTRICAL:

• Capacitors

•  Temperature Limit Switches

• Compressors

• Thermostats

• Contactors

•  Time Delay Relays

•  Pressure Switches

• Transformers

• Relays

MOTORS:

•  Blower Motor

•  Fan Motor

COMPONENTS:

•  Blower Assembly

•  Fan Grille

•  Cabinet Panels

• Filter/Driers

•  Expansion Valves

Specifications & illustrations subject to change without notice or incurring obligations (07/22).
O’Fallon, MO, © Nortek Global HVAC LLC 2022. All Rights Reserved.

10414110

(NEW)

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Rated Voltage:

Max. deviation of voltage from avg. volts:

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting

correct? (If Applicable)

YES

NO

Summary of Contents for SA3BF4M2SN Series













Reviews: