background image

INSTALLATION CHECKLIST

REFRIGERATION SYSTEM

Was unit given 24 hr warm up period

for crankcase heaters (if applicable)?

YES

NO

Stage-1 Liquid Pressure:

HIGH

SIDE:

Stage-1 Suction Pressure:

LOW

SIDE:

INSTALLER: PLEASE LEAVE THESE

INSTRUCTIONS WITH THE OWNER.

INSTALLATION ADDRESS:

CITY:

STATE:

UNIT MODEL #:

UNIT SERIAL #:

Unit Installed Minimum clearances per

Figure 2 (page 6)

YES

NO

INSTALLER NAME:

CITY

STATE

Has the owner’s information been

reviewed with the customer?

YES

NO

Has the Literature Package been left

with the unit?

YES

NO

FILTER SYSTEM

Filter(s) secured in place?

YES

NO

Filter(s) clean?

YES

NO

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Rated Voltage:

VOLTS:

L1-L2 Volts:

VOLTS:

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct?

YES

NO

REPLACEMENT PARTS

Replacement parts are available through your distributor. 

Please have the complete model and serial number of 

the unit when ordering replacement parts.

ELECTRICAL:

•  Ambient Sensor

• Contactors

• Capacitors

•  Pressure Switches

•  Coil Sensor

• Relays

• Compressors

• Transformers

MOTORS:

•  Blower Motor
•  Fan Motor

COMPONENTS:

•  Blower Assembly

•  Fan Grille

•  Cabinet Panels

• Filter/Driers

•  Expansion Valves

PROPOSITION 65 WARNING:

WARNING: This product contains chemicals known 
to the state of California to cause cancer.

WARNING: This product contains chemicals known 
to the state of California to cause birth defects or 
other reproductive harm.

Specifications & illustrations subject to change without notice or incurring obligations (08/22).
O’Fallon, MO, © Nortek Global HVAC LLC 2022. All Rights Reserved.

10414730

(NEW)

Summary of Contents for Q104SD Series





















Reviews: