background image

Single Package Air Conditioner - Single Stage, R-410A

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

IMPORTANT

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being 
able to install the product according to strict safety guidelines and instructing the customer on 
how to operate and maintain the equipment for the life of the product. Safety should always be 
the deciding factor when installing this product and using common sense plays an important 
role as well. Pay attention to all safety warnings and any other special notes highlighted in the 
manual. Improper installation of the furnace or failure to follow safety warnings could result 
in serious injury, death, or property damage.

These instructions are primarily intended to assist qualified individuals experienced in the 
proper installation of this appliance. Some local codes require licensed installation/service 
personnel for this type of equipment. Please read all instructions carefully before starting the 
installation. Return these instructions to the customer’s package for future reference.

13 SEER

P7RD-A / PPA3RDA SERIES

INSTALLATION INSTRUCTIONS

Summary of Contents for P7RD-A Series





















Reviews: