background image

7

CIRCULATING AIR REQUIREMENTS

 WARNING:

Do not allow combustion products to enter the 

circulating air supply. Failure to prevent the 

circulation of combustion products into the 

living space can create potentially hazardous 

conditions including carbon monoxide poisoning 

that could result in personal injury or death.

The surface that the furnace is mounted on must 

provide sound physical support of the furnace 

with no gaps, cracks or sagging between the 

furnace and the floor or platform.
Circulating air ductwork must not be connected 

to any other heat producing device such as a 

fireplace insert, stove, etc. This may result in fire, 

explosion, carbon monoxide poisoning, personal 

injury, or property damage.

Return Air

U.S.A. home manufacturers shall comply with all of the 

following conditions to have acceptable return air systems 

for closet installed forced air heating appliances:

•  The return air opening into the closet shall not be less 

than specified in the appliance’s listing.

• The cross-sectional area of the return duct system 

leading into the closet, when located in the floor or 

ceiling shall not be less than 235 in

2

.

 CAUTION:

HAZARD OF ASPHYXIATION: Do not cover or 

restrict return air opening.

•  Means shall be provided that prevent inadvertent closure 

of flat objects placed over the return air opening located 

in the floor of the closet (versus the vertical front or side 

wall).

• The total free area of openings in the floor or ceiling 

registers serving the return air duct system must be at 

least 235 in

2

. At least one register should be located 

where it is not likely to be covered by carpeting, boxes 

and other objects.

•  Materials located in the return duct system must have a 

flame spread classification of 200 or less. This includes 

a closet door if the furnace is in a closet.

•  Noncombustible pans having 1” upturned flanges are 

located beneath openings in a floor duct system.

•  Wiring materials located in the return duct system shall 

conform to Articles 300-22 of the National Electrical 

Code (ANSI C1/NFPA-70).

•  Gas piping is not run in or through the return duct system.

 CAUTION:

HAZARD OF ASPHYXIATION: Negative pressure 

inside the closet, with closet door closed and 

the furnace blower operating on high speed, 

shall be no more negative than minus 0.05 inch 

water column.

• Test the negative pressure in the closet with the air-

circulating fan operating at high speed and the closet 

closed. The negative pressure is to be no more negative 

than minus 0.05 inch water column.

•  Air conditioning systems may require more duct register 

and open louver area to obtain necessary airflow.

Supply Air

For proper air distribution, the supply duct system must be 

designed so that the static pressure measured external 

to the furnace does not exceed the listed static pressure 

rating shown on the furnace rating plate.
Location, size, and number of registers should be selected 

on the basis of best air distribution and floor plan of 

the home. 

The supply air must be delivered to the 

conditioned space by duct(s) secured to the furnace 

casing, running full size and without interruption.

 

Three typical distribution systems are shown in 

Figure 5

FURNACE INSTALLATION

NOTE: 

These Installation procedures are suggested for 

typical furnace installations. Since each installation is 

different, the sequence of instructions may differ from 

the actual installation. Only qualified HVAC technicians 

should install this furnace.
The installer must be familiar with and comply with all 

codes and regulations applicable to the installation of 

these heating appliances and related equipment. In 

the absence of local codes, the installation must be in 

accordance with the current provisions of one or more of 

the following standards.

• Federal Manufactured Home Constructions & Safety 

Standard (H.U.D. Title 24, Part 3280.707[a][2])

•  American National Standard (ANSI-119.2/NFPA-501C) 

for all recreational vehicle installations.

•  American National Standard (ANSI-Z223.1/NFPA-54) 

and/or CAN/CSA B149 for all gas-fired furnace models.

• American National Standard (ANSI-Z95.1/NFPA-31) 

and/or CSA B139 for all oil-fired furnace models.

Figure 5. Typical Supply Duct System

A Single trunk duct

B Dual trunk duct

w/crossover connector

C

Transition duct

   w/branches

Summary of Contents for MG1 Series

































Reviews: