2
Z-WAVE PROGRAMMING
Adding to a Network:
Refer to your Controller operating instructions to add this device under the
command of the Wireless Controller.
1.
Remove the small case screw and open the rear of the sensor.
2.
Install the CR123 battery into the sensor’s battery holder.
3.
With your Controller in Discovery or Add Mode, press the
PROGRAM
switch. The red indicator will blink slowly.
4.
When the FloodZ is added, the indicator will stay on.
5.
You should see an indication on your Controller that the “device was added”
to the network.
If the Controller/Gateway shows the addition failed, repeat Steps 1-3.
✓
NOTE:
If you have trouble adding the WF00Z-1 to a network it may be that
the Home ID and Node ID were not cleared from it after testing. You must
fi rst “RESET UNIT” or remove it from the network.
To Reset Unit (If Required):
In the event that your primary Controller is lost or otherwise inoperable, to reset
the WF00Z-1 and clear all network information, follow these steps:
1.
Remove the cover of the WF00Z-1.
2.
Dip the sensor into a shallow cup of water to trigger the device 5 times
within 10 seconds.
3.
The WF00Z-1 will completely reset to factory defaults.
Removing from a Network:
The WF00Z-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1.
Remove the cover of the WF00Z-1.
2.
With the Controller in Remove Mode, press the
PROGRAM
switch for
1 second.
3.
You should see an indication on your Controller that the device was removed
from the network.
Associations
1.
Remove the cover of the WF00Z-1 to initiate the “Awake” mode.
2.
Put the Controller into “Association”, and following its instruction to
associate the WF00Z-1 to other devices.
3.
Replace the cover after “Association” is complete.
The WF00Z-1 will get into “Sleep” mode for power saving.
Support grouping identifi er = 1. Also supports one association group (5 nodes).
“Association” is used for other grouped devices triggering.
Z-Wave Command Classes
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_
B
ATTERY
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
SPECIFICATIONS
Power:
CR123A Lithium Ion battery (included)
Signal (Frequency):
908.42 MHz / 916 MHz
Range:
Up to 130 feet line of sight
REGULATORY INFORMATION
The WF00Z-1 is certifi ed to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class
B
digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment
IC Notice
This Class
B
digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe
B
est conforme à la norme NM
B
-003 du Canada. Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
WARRANTY
What is Covered?
Nortek Security & Control (“NS&C”) warrants to consumers who purchase this product for personal, family or
household purposes new from NS&C directly or from an authorized NS&C dealer, that the product will be free from
defects in materials and workmanship for a period of (1) year from the date of purchase. This warranty only applies if
the product is installed at a residence in the 50 United States or District of Columbia, and only at the site of the original
installation. It is not transferable. This warranty is not extended to resellers.
If a defect exists, NS&C will have you ship the defective part or product to us and we will, at our option, either repair
or replace it. This warranty does
not
cover the cost of labor to remove a defective part or product or to reinstall any
repaired or replacement part or product.
This warranty does
not
cover defects or damages caused by improper handling, maintenance, storage, installation,
removal or re-installation, misuse, non-factory authorized modifi cation or alteration, use of incompatible accessories,
electrical power problems or surges, impact by foreign objects, accident, fi re, acts of God, normal wear and tear
or shipping damage other than a shipment from NS&C. Note that all NS&C products are designed to be installed,
removed and serviced by trained individuals or professionals.
Keep your original sales receipt as it will be required to obtain warranty service.
This warranty shall not be extended or restarted upon receipt of any repaired or replacement part or product under this
warranty. No person is authorized to extend or otherwise modify this warranty.
How do I Obtain Warranty Service?
To obtain warranty service, email our Returns Department at [email protected]. Include your name, address,
telephone number, the model number of your product, a copy of your original sales receipt, and a description of the
problem. Unless we need to discuss the situation further with you, you will be emailed a Return Authorization Number
and shipping instructions. If we need to discuss the situation further with you, we will call or email you. NS&C may
require troubleshooting on installed product before a Return Authorization Number is issued. Anything shipped to us
without a Return Authorization Number will be automatically returned unopened. You are responsible for the charges
for shipment to us, unless you are a California resident.
Limitations
THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT
EXCEED THE WARRANTY PERIOD PROVIDED HEREIN.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
NS&C SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE BREACH OF ANY WRITTEN OR IMPLIED
WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
This warranty gives you specifi c legal rights, and you may also have other legal rights which vary from State to State.
IMPORTANT !!!
Radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling.
However, there are some limitations which must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices.
As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that
occur on or near their operating frequencies, regardless of code settings.
• Changes or modifications to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer,
and these facts should be communicated to the ultimate users.
Copyright © 2016 Nortek Security & Control LLC
10008416 X6
IN
S
E
R
T BATTE
R
Y
INTO T
R
AN
S
MITTE
R
P
R
O
GR
AM
S
WITCH
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,WF00Z-1, GO CONTROL; P/N: 10008416 X6; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: FLAT 8.500” x 11.000”, FOLDED 4.250” x 2.750”; TOLERANCE ± .125”; SCALE: 1-1 PAGE 2 OF 2
