Quick Installation Guide
LNVR1-08P / LNVR1-16P
SATA2
SATA1
J3
SATA Data x2
SATA Power x1
SATA power SATA data
4
3
Warning Before Installation
Avertissement avant installation
Advertencia antes de la instalación
Power off the Network Video Recorder if you detect
abnormal smell or smoke coming from it.
Éteignez rapidement le magnétoscope de réseau s’il
dégage de la fumée ou une odeur inhabituelle.
Apague el Grabador de Vídeo de Red si aparece
humo o algún olor no habitual.
Keep the Network Video Recorder away from water. If
the Video Recorder is wet, power off immediately.
Tenez le magnétoscope de réseau éloigné de l’eau. Si
le magnétoscope de réseau est mouillé, éteignez le
immédiatement.
Mantenga el Grabador de Vídeo de Red alejado
del agua. Si el Grabador de Vídeo de Red se moja,
apáguelo inmediatamente.
Do not place the Network Video Recorder in high
humidity environments.
Ne placez pas le magnétoscope de réseau dans un
environnement très humide.
No coloque el Grabador de Vídeo de Red en entornos
con mucha humedad.
Do not place the Network Video Recorder around
the heat sources, such as television or oven.
Ne placez pas le magnétoscope de réseau à
proximité d’une sources de chaleur, comme un
téléviseur ou un four.
No coloque el Grabador de Vídeo de Red junto a
fuentes de calor, como por ejemplo televisores u
hornos.
Do not drop the Network Camera.
Tenez le magnétoscope de réseau éloigné de la
lumière directe du soleil.
Mantenga el Grabador de Vídeo de Red alejado de
la luz directa del so
PLEASE NOTE: VIVOTEK does not provide warranty or technical support for third party application software that
users additionally install and run on the NR9681.
No intente quitar o desinstalar el software en la
memoria flash montada.
Do not attempt to remove or uninstall the software on
the mounted flash memory.
Ne tentez pas de retirer ou de désinstaller le logiciel
sur la mémoire flash montée.
5
Package Contents / Vérifier le contenu de l’emballage / Compruebe el contenido del embalaje
NVR
Rack Ears
AC Power Cord
x 8
HDD Mounting
Screws
Rubber Feet
Quick Install
Guide
Mouse
SATA HDD Cable
6
x6
Reinstall the mounting the cover and the six (6) cover screws.
PRINTER’S INSTRUCTIONS:
INSTR, QUICK START GUIDE, LNVR1-08P/16P, LINEAR - P/N: 10030185 Rev-B - INK: BLACK, CMYK - MATERIAL: 70 LB WHITE - SIZE: 390mm X 549mm - TOL ± .040” - SCALE: 1-1 - FOLD TO 195 x 274.5 mm
1
2
Apply the rubber feet if NVR will sit on desk or shelf. Not
required for rack mounting.
If adding a second HDD, insert four supplied screws into the HDD (leaving them loose).
Position the HDD screws through the large end of the slotted mounting holes on the bottom of the NVR chassis, slide it over,
then tighten the mounting screws.
Attach the SATA Power and Data cables to HDD.
The NVR can support two Hard Disk Drives. It comes
equipped with one HDD to add another HDD follow the
below instructions.
Remove the six (6) screws that attach the top cover and
slide the cover back to remove.
If adding a second HDD, attach the SATA Data cable to
the SATA2 connector on the NVR mother board.
