Nortech F20 User Manual Download

Page: 14 / 16

F20

Twin Earth Fault Indicator

Page 14 of 16

Specification

6.1

General

Power Supply

3.6V Lithium battery. The battery is plug in for simple
replacement.
OR
12-24V dc external supply.

Threshold current

45 Amps nominal

Indicator

Ultra bright LEDs, one for each Earth Fault element.
1.5 seconds flash rate
3

–

24 hours duration (as ordered) or until reset by

manual (button) or voltage reset

Remote Alarm options Volt free change-over contacts. Normally open and

normally closed contacts are provided.
One set of contacts for each Earth Fault element.

DC Remote Reset

12V-24V dc for 1000ms

AC Remote Reset

90V-240V ac for 10 seconds

6.2

EMC

The F20 indicator has been designed for compliance in accordance with the
high level standard 61326-1:2006 industrial class.

Immunity

ESD

IEC61000-4-2

4kV contact, 8kV air

EM Field

IEC61000-4-3

10V/m 80MHz-1GHz
3V/m 1GHz-2GHz
3V/m 2.0GHz-2.7GHz

Power Freq Mag Field

IEC61000-4-8

Not Applicable

Power and I/O Signal Lines

Burst (Fast Transient) IEC61000-4-4

Not Applicable

Surge

IEC61000-4-5

Not Applicable

Conducted RF

IEC61000-4-6

Not Applicable

Voltage Dips and
Interruptions

IEC61000-4-11 Not Applicable

Voltage Dips and
Interruptions

IEC61000-4-11 Not Applicable

Emissions

Radiated Emissions

EN55011

Class B

Insulation

1kV RMS for 1 minute insulation tests on NO/NC contact

Not called for by the standard

Summary of Contents for F20

















Search results

Summary of Contents for F20

Reviews:

Related manuals for F20

Brands by name

Popular brands

Nortech F20, User Manual

Search results

Summary of Contents for F20

Reviews:

Related manuals for F20

Brands by name

Popular brands