Normstahl EasyLift 500, Translation Of The Original Operating Manual, Page: 19 / 56

EasyLift 500 / Sesam 600 MA120527=>2012-05 19 / 56
ATTENTION: No protection is provided by the load
switch-off whilst the door operator is being taught
in.
Note : Teaching in is only possible during initial installation or
after resetting the door operator. Do not press any button
during the teach-in procedure.
Preparation : Connect the door to the door operator.
Teach in travel distance and force values
• Press and hold the CANC button (12).
• Press and hold the TEST button (13) until LED1 (red) and
LED2 (green) flash alternately.
• When both LED‘s no longer flash, release both
buttons (12+13).
• Wait until both LED‘s (1+2) flash in sync.
• Press and hold the TEST button (13) until the door is
almost closed.
• Close the door completely in jog mode (tap the TEST
button to move the door) (door position closed), LED 1
(red) lights *.
• Teach in door position closed by pressing the CANC button
(12), LED 1 (red) goes out and LED 2 (green) lights up.
• Press and hold the TEST button (13) until the door is
almost fully open.
• Open the door fully in jog mode (tap the TEST button to
move the door).
• Teach in door position open by pressing the CANC button
(12), LED 1 (red) lights up and LED 2 (green) goes out.
• Teach in force values by pressing the TEST button (13),
the operator closes and opens the door, LED 1 (red) LED 2
(green) flash alternately. When the force values have been
taught in, only LED 1 (red) flashes.
The door operator is taught in.
* If the operator has moved too far when setting “door position
closed” (chain hanging out of the rail runner)
• Press the CANC button (12).
• Open the door half way with the TEST button (13).
• Pull out the mains plug, wait about 5 seconds and plug it
back in.
• Teach in travel distance and force values again.
Teach in remote transmitter:
• Press the PROG button (11), LED 2 (green) lights up.
• Press the desired button on the remote transmitter, LED 2
goes out.
• Press the desired button on the remote transmitter, LED 2
flashes slowly and goes out.
The remote transmitter is taught in.
Deleting (all) remote transmitter(s):
• Press and hold the PROG button (11) until LED 2 (green)
flashes rapidly.
• Release the PROG button, all saved remote transmitters
are deleted.
CAUTION : Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY
STOP) can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.
ATTENTION: There is no longer any protection by
switching off the load after the reset.
Teach the
door operator in again before re-commissioning. For this
carry out
Teaching in the Door Operator (Chapter 15) .
• Press and hold the CANC button (12).
• Press and hold the TEST button (13) until LED1 (red) and
LED2 (green) flash alternately.
• When both LED‘s no longer flash, release both
buttons (12+13).
• Wait until both LED‘s (1+2) flash in sync, all values are now
deleted.
Connect the light barrier as illustrated (remove jumper
between connection 6+7)
15 Teaching in the Door Operator
16 Teaching in/Deleting a Remote
Transmitter
17 Operation
18 Reset
19 Connecting the Light Barrier
5 = GND
6 = Signal
7 = 24V
STORING A RADIO TRANSMITTER:
- Press the PROG(11) button; LED 2 (green) and the red
LED on the radio receiver card come on
- Press the desired button on the transmitter; LED 2 (green)
and/or the red LED on the radio receiver go out and then
come on again.
- Press the desired button on the transmitter again; LED 2
(green) and/or the red LED on the radio receiver flash on
and off. The transmitter has now been stored.
..
DELETING ALL RADIO TRANSMITTERS:
- Hold down the PROG(11) button until the red LED on the
radio receiver flashes on and off
- Release the PROG button and press it again until the red
LED on the radio receiver rapidly flashes on and off; all the
stored radio transmitters have been deleted