background image

3

 Outdoor

 

Installation Location

1. Outdoor Installation Area Operating Conditions.

  • Ensure ambient temperatures are higher than 5°F /-15°C.

  • Prevent the air from becoming contaminated by the products, places, and conditions listed in the

   water heater installation manual.

WARNING

Carefully consider installation when determining water heater location. Please read the entire installation

manual and these instructions before attempting installation. Failure to properly take factors such as piping,

condensate removal, venting, and wiring into account before installation could result in wasted time, money,

and possible property damage, personal injury, or death.

The outdoor kit is meant for use in outdoor installations ONLY. DO NOT install the water heater with 

outdoor kit indoors. Installing the water heater with outdoor kit indoors will result in improper water heater 

operation and property damage, and could result in serious personal injury or death.

WARNING

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk. 

Ensure that the installation location adheres to the information included in this manual. Failure to do so 

could result in property damage, serious personal injury, or death. Failure of heater or components due to 

incorrect operating conditions IS NOT covered by product warranty.

The water heater must be installed as described in these instructions: Upright, with the suppled outdoor 

enclosure in the vertical position. DO NOT attempt to install the water heater in any other orientation. Failure 

to follow these instructions will result in improper water heater operation and property damage, and could 

result in serious personal injury or death.

2. Check for nearby connections to: 

  • System water piping

  • Venting connections   

  • Gas supply piping

  • Electrical power

  • Condensate drain

Note:

The manufacturer reserves the right to make changes or updates 

without notice and will not be held liable for errors in literature.

Install the water heater where any leakage from the relief valve, related piping, tank, or connections will not 

result in damage to surrounding areas, lower floors of the building, or  pool on the ground and freeze. 

The water heater should be located near a drain or piped to a drain. Leakage damages ARE NOT covered 

by warranty.

CAUTION

Summary of Contents for VCK-NRCP-1












Reviews: