Noritz NRC661-DV Service Manual Download Page 62

Setting list for MW settings and Gas manifold pressures    (Check the rating plate for model and gas type)

Manual Programming

1. Make sure the remote controller is off ( completely blank ),  If it is ON, turn it OFF and wait for 10 seconds.

(only do this if the data transfer on the previous page is unsuccessful)

This procedure will require the remote controller.

Make sure the circuit board is completely connected.

2. ...then disconnect

    electrical power.

3. Wait 10 seconds and reconnect power.

    Leave the remote controller off.

PRIORITY light

UP / DOWN button

display

( MW number )

power ON/OFF button

FLOW METER ALARM SET button

4. With the remote controller blank, press the up button until the display blinks "99".

    You are now in the maintenance writer (MW) mode and can scroll through the

    MWs using the UP and DOWN buttons.

[ Remote controller ]

5. Once complete, hold the UP and DOWN buttons together for five seconds until the remote

    controller starts beeping rapidly.

   This is the signal that the changes to the MWs have been saved and the unit is ready for use.

6. Check manifold pressures with a digital manometer and adjust if necessary.

    For each MW the PRIORITY light will either be on, indicating that the MW is

    ON, or off, indicating the MW is OFF.

    You can toggle each MW to be ON or OFF using the FLOW METER ALARM SET

    button.
    a)  MW "#23" must be ON for all units except the NRC661-DV/OD.

    b)  Turn MW "FC" and "FE" ON and press the UP or DOWN button.

         (Display blinks with "A0 ". )

         Configure the remaining MWs according to the chart below based on your unit's

         model and gas type.

Model

Gas type

Circuit board MW setting

A1

NRC661-DV

LPG

Natural

Min value

Max value

NRC661-OD

LPG

Natural

Vent Length Adjustment

-DV(-SV) Model only

Dip Switch 7 Vent Length

Short Length

Long Length

Short Length

Long Length

(

:ON

:OFF

)

1.05

3.15

1.05

3.20

1.30

3.15

1.30

3.15

1.05

3.10

1.20

3.20

NRC711-DV

NRC711-OD

NR501-OD

NR662-OD

3.05

3.10

3.55

3.60

2.75

3.45

2.70

3.05

2.80

2.85

1.05

1.05

1.20

1.20

0.95

1.20

1.05

1.25

1.25

1.30

LPG

Natural

LPG

Natural

LPG

Natural

LPG

Natural

LPG

Natural

Short Length

Long Length

Short Length

Long Length

A2 A3 A4 A5 A6

A8 A9 AA AB AE AF B0 B1 BC

A7

C8

Manifold Pressure (inch H

2

O)

Cover off

NRC661A-DV

NRC661A-OD

Natural

LPG

Short Length

Long Length

Short Length

Long Length

1.05

3.15

1.05

3.20

1.30

3.15

1.30

3.15

1.05

3.10

1.20

3.20

LPG

Natural

62

Summary of Contents for NRC661-DV















































































Reviews: