Noritz NC1991-OD Installation Manual Download Page 5

5

•  Avoid places where fires are common, such as those where gasoline, 

benzene and adhesives are handled, or places in which corrosive gases 

(ammonia, chlorine, sulfur, ethylene compounds, acids) are present.

     Using the incorrect voltage may result in fire or cracking.
•  Avoid installation in places where dust or debris will accumulate.

Dust may block the air-supply opening, causing the performance of the 

device fan to drop and incomplete combustion to occur as a result.

•  Avoid installation in places where special chemical agents 

  (e.g., hair spray or spray detergent) are used.

Ignition failures and malfunction may occur as a result.

•  Carbon Monoxide Poisoning Hazard. Do not install this water heater in a 

mobile home, recreational vehicle or on a boat.

•  Install the water heater in a location where it is free from obstacles and 

stagnant air.

•  Consult with the customer concerning the location of installation.

•  Do not install the water heater near staircases or emergency exits.

•  Do not install the water heater where the exhaust will blow on outer walls 

or material not resistant to heat. Also consider the surrounding trees and 
animals.

The heat and moisture from the water heater may cause discoloration of 
walls and resinous materials, or corrosion of aluminum materials.

•  Do not locate the vent termination directed towards a window or any 

other structure which has glass or wired glass facing the termination.

•  Install in a location where the exhaust gas flow will not be affected by 

fans or range hoods.

•  Take care that noise and exhaust gas will not affect neighbors.   

Avoid installation on common walls as the unit will make some 

operational noises while it is running.

•  Avoid installation where the unit will be exposed to excessive winds.
•  Before installing, make sure that the vent termination will have the proper 

clearances according to the National Fuel Gas Code (ANSI Z223.1).

Prohibited

WARNING

CAUTION

Prohibited

State  of  California: The  water  heater  must  be  braced,  anchored  or  strapped  to  avoid  moving  during 

an earthquake. Contact local utilities for code requirements in your area or call: 1-866-766-7489 and 
request instructions.

The Commonwealth of Massachusetts:

1) The outdoor units (OD) can only be used if they are for summer use only.

2) The water heater can be used for hot water only and not in a combination of domestic and space 

heating.

Summary of Contents for NC1991-OD































Reviews: