Noritz ecoTOUGH NRC711-OD Installation Manual Download Page 17

17

Combination Potable Water and Space Heating System

Isolation

Kit(*1)

Gas Supply

Backflow Preventer

(optional)

Check

Valve(*3)

Cold Water

Supply

Mixing Valve(*5)

Hot Water

Pump(*2)

Flow Switch(*4)

Fixtures

Air Handler

Optional

Expansion Tank(*6)

Recirculation System

Cold Water Supply

Isolation

Kit(*

)

Gas Supply

Aquastat(*2)

Hot Water

Optional 8-10 Gallon

Storage Tank

(To alleviate cold water sandwich)

Globe

Valve

Pump(*1)

Expansion Tank

(Install according

to local code)

Fixtures

Hot Water Return

R

B

W

Pump

120VAC

105

Neutral

Ground

Live

S

Notes:

Use Honeywell Aquastat 

(Model L6006A or L6006C)

Aquastat Wiring

1. Size the pump to provide a maximum of 1.5GPM 

    (5.7L/min.) through the system at 10ft (0.3m) of 

    head plus piping losses. 

    Adjust the flow using a globe valve and verify the 

    flow rate with the maintenance monitors.

2. Set the Aquastat to 10˚F below the set output 

    temperature. 

3. Noritz recommends the use of an Isolation Kit

    with the installation.

    These kits include an integrated shut-off and service 

    valve with unions and a pressure relief valve. 

Notes:

1. Noritz recommends the use of an Isolation Kit with

    the installation.

    These kits include an integrated shut-off and service 

    valve with unions and a pressure relief valve.

2. Size the pump to provide a maximum of 2 GPM

    (7.5 L/min.) with a head pressure equal to the loss 

    through the water heater and Air Handler.

3. Check valve required if it is not included with the pump.
4. Set the flow switch to deactivate the Air Handler when

    the domestic hot water flow reaches 2 GPM (7.5 L/min.).

    Adjust as necessary to prevent cycling.  
5. If the system requires water for space heating at a higher 

    temperature than for other uses, means such as a

    mixing valve shall be provided to temper the water for

    the other uses to help prevent scalding.

7. The water heater cannot be used for space heating 

    applications only.
8. Only POTABLE water may be plumbed through

    the water heater.

6. Expansion tank required if a backflow preventer is installed.

NORITZ

Condensing

Tankless Gas

Water Heater

NORITZ

Condensing

Tankless Gas

Water Heater

10.

 

Plumbing Applications

▲The illustration is an example. Please check with the actual water heater about the position of piping, and form.

Summary of Contents for ecoTOUGH NRC711-OD



























Reviews: