Batteries
• Your new Trimmer requires
2 “AA” 1.5 V alkaline or
carbon zinc batteries.
To Insert Batteries
1. Be certain Trimmer is in
the OFF position.
2. Hold Trimmer horizontally
and press the release tabs
located at base of
Trimmer. Gently slide bat-
tery compartment out of
Trimmer housing until it
stops (Fig. 1)
NOTE:
Battery compart-
ment is not removable.
3. Insert the batteries as
shown making sure the (+)
and (-) markings on the
batteries match those on
inside compartment of
Trimmer (Fig. 2).
4. Slide the battery
compartment back into
Trimmer housing (Fig. 3).
NOTE:
Trimmer will not
operate if batteries are
inserted incorrectly. If you
do not intend to use the
appliance for a long time,
remove the batteries.
Leaking batteries can cause
damage to the product.
To Remove Batteries
1. Follow steps 1-2 above.
Push the batteries out of the
holder as shown (Fig. 4).
•
Trimmer Guard
Attachment must be in
place on the Trimmer in
order to use the Zoom
Ring.
• Zoom Ring with Trimmer
Guard Attachment ensures
precise trimming and has
9 adjustable settings (see
chart below).
• Zoom Ring will “click” into
position at each setting.
• Start at a longer setting
(#7, 8 or 9) to prevent
accidentally trimming
hairs too short (Fig. 5).
• Trim against the direction
of hair growth (Fig. 6)
• As you become familiar
with the settings, adjust
Zoom Ring to desired
trimming length.
To Remove
• Remove Trimmer Guard
Attachment if you are:
• Defining hair lines
• Trimming nape of neck
• Removing single, unwant-
ed hairs
1. Be certain Trimmer is in
the OFF position.
2. Hold Trimmer base with
one hand, grasp sides of
Trimmer Guard Attach-
ment and gently slide
Attachment off Trimmer
(Fig. 7).
NOTE:
Zoom Ring can be
on any setting when
removing or replacing
Trimmer Guard
Attachment.
To Replace
1. Be certain Trimmer is in
the OFF position.
2. Hold Trimmer in one hand
and replace Attachment
back onto Trimmer until it
“clicks” into position.
NOTE:
The Trimmer Guard
Attachment can be placed
on Trimmer only one way.
If it does not fit properly,
reverse it.
To Trim Beard
1. Comb hairs outward so
that they are at their maxi-
mum height and in the
same direction.
2. With Trimmer Guard
Attachment in place,
set Zoom Ring to desired
setting.
3. Slide On/Off switch to the
ON position and begin
trimming (Fig. 8).
4. Turn Trimmer OFF.
IMPORTANT:
If using Trimmer
without Trimmer Guard
Attachment, use a slow, very
light “skimming” technique to
prevent trimming off more than
the desired amount of hair.
To Trim Outer Edge of Beard
& Add Definition
1. Remove Trimmer Guard
Attachment.
2. Hold Trimmer diagonally
with front of Trimmer fac-
ing away from you (Fig. 9).
3. Turn Trimmer ON.
4. Start at chin and work
back toward ear.
5. Follow line of jawbone to
cut away longer hairs on
outer edge of beard.
6. Turn Trimmer OFF.
NOTE:
Practice is best for
optimum results.
1
2
3
CLICK
4
5
6
8
7
9
6
6
7
8
9
1
2
3
4
5
Hair Length Selector
#1
Stubble Length or Closely Cropped
.06 in./1.5 mm
#2
Short
.1 in./2.5 mm
#3
.16 in./4 mm
#4
.22 in./5.5 mm
#5
Medium
.3 in./7.5 mm
#6
.38 in./9.5 mm
#7
.48 in./12 mm
#8
.6 in./15 mm
#9
Long
.72 in./18 mm
7
8
Trimmer Guard Attachment
9
