Nordson Encore LT Product Manual Download Page 57

Page: 57 / 92

Repair

6-1

Part 1604857-04

2014 Nordson Corporation

Section 6

Repair

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

Spray Gun Repair

NOTE:

All item numbers in the spray gun repair illustrations are the same

as the item numbers in the spray gun parts list.

Power Supply and Powder Path Replacement

Gun Disassembly

1. See Figure 6-1. Remove the nozzle nut, nozzle, and electrode assembly

(1, 2, 3).

2. Remove the screws (11, 12) and hook, cover, and housing (8, 9, 10).
3. Pull the power supply harness out of the bulkhead, then insert a small

flat-bladed screwdriver into the recess in the harness connector to

release the catch. Disconnect the gun cable from the power supply

harness.

Power Supply Connectors

Trigger Connectors

Figure 6-1

Gun Disassembly

1. Nozzle nut
2. Nozzle
3. Electrode assembly

8. Cover
9. Housing

10. Hook

11. M3 x 30 screw

12. M3 x 20 screw

Summary of Contents for Encore LT





























































































Search results

Summary of Contents for Encore LT

Reviews:

Nordson Encore LT, Product Manual, Page: 57 / 92

Search results

Summary of Contents for Encore LT

Reviews: