manualshive.com logo in svg

Nordson Asymtek Spectrum S-920, Installation, Operation & Maintenance Manual, Page: 174 / 238

Share
Download
Nordson Asymtek Spectrum S-920 Installation, Operation & Maintenance Manual Download Page 174

7-14  

Maintenance 

 

7.10  Tensioning the Conveyor Belts 

To tension the conveyor belts: 

1.

 

Perform a service shutdown as specified in 

2.11 Service Shutdown

. 

2.

 

Loosen the belt tensioner screws (Figure 7-10). 

3.

 

Move the Motor Mount Tensioner up and down until the desired tension is obtained. 

4.

 

Tighten the tensioner screws. 

5.

 

Repeat Steps 1-3 for the other belt. 

 

Item Description Item Description 

1 

Motor Mount Tensioner - Rear Rail 

4 

Belt Tensioner Screws - Rear Rail (4) 

2 

Conveyor Belt 

5 

Motor Mount Tensioner - Front Rail 

3 

Belt Drive Pulley 

6 

Belt Tensioner Screws - Front Rail (4) 

Figure 7-10   Tensioning the Conveyor Belts 

"

 

NOTE

  If the conveyor belts need to be replaced, refer to 

9.7 Replacing the Conveyor Belts.

 

1 

2

3

5

6

4

Summary of Contents for Asymtek Spectrum S-920















































































































































































































































Reviews:

No comments