manualshive.com logo in svg

Nordson Asymtek Spectrum S-920, Installation, Operation & Maintenance Manual, Page: 173 / 238

Share
Download
Nordson Asymtek Spectrum S-920 Installation, Operation & Maintenance Manual Download Page 173

Maintenance  

7-13 

7.9 

Tensioning the Cables 

To tension the cables: 

1.

 

Perform a service shutdown as specified in 

2.11 Service Shutdown

. 

2.

 

Remove the X- and Y-axis covers. See 

7.7 Removing the Axis Covers

. 

3.

 

Loosen the X-Axis and two (2) Y-axis tensioner screws.   

4.

 

Move the Z-head in a circle around the dispensing area approximately 5 times. 

5.

 

Stop in the middle. 

6.

 

Retighten the tensioner screws. 

 

 

 

Figure 7-9A   Tensioning the X-Axis Cables 

Figure 7-9B Tensioning the Y-Axis Cables 

 

Item Description 

1 

X-Axis Tensioner Screw 

2 

Y-Axis Tensioner Screw 

Figure 7-9   Tensioning the Cables 

1

2 

Summary of Contents for Asymtek Spectrum S-920















































































































































































































































Reviews:

No comments