manualshive.com logo in svg

Nordson Asymtek Spectrum S-920, Installation, Operation & Maintenance Manual

Share
Download
Nordson Asymtek Spectrum S-920 Installation, Operation & Maintenance Manual Download Page 126

6-2  

Operation 

 

6.4 

Installing the Dispensing Valve 

To install the dispensing valve, slide the dovetail bracket (included with the dispensing valve) into the 
valve mounting bracket on the Z-axis face plate. Secure by turning the lever on the valve mounting 
bracket to the upward position. Refer to the applicable dispensing valve manual for additional 
information.   

6.4.1  Valve Pneumatic and Electrical Connections 

Valve pneumatic and electrical connections are shown in Figure 6-1 and Figure 6-2. Refer to the manual 
for your particular dispensing valve for additional information.  

 

Item Description Item 

Description 

1 

Fluid Air Pressure (Clear) 

3 

DV-Series Valve  

2 

Valve Electrical Connection 

 

 

Figure 6-1   Valve Pneumatic and Electrical Connections (DV-8000 shown) 

1

2

3

Summary of Contents for Asymtek Spectrum S-920















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands