background image

GB

Two-zone setting for serving 

temperature

Typical serving temperature settings for the 

top and bottom sections are 16°C and 6°C 

respectively. With these settings, a suitable 

temperature gradient will be achieved in 

the cabinet for the storage of various types 

of wine distributed from top to bottom as 

follows:

 

heavy red wines +16 to +19°C

 

rosé and light red wines +12 to +16°C

 

white wines +10 to +12°C

 

champagne and sparkling wines +6 to 

+8°C

It is recommended that wine be served at a 

temperature which is a couple of degrees 

lower than the desired drinking temperature 

as the wine will be warmed slightly when it 

is poured into the glass. 

Temperature setting at the bot-

tom of the appliance

Push SET2. Then the temperature at the 

bottom of the appliance can be adjusted up 

and down by means of the “up and down” 

buttons. The temperature can be adjusted 

from 5 to 22°C, however so that the tem-

perature cannot be set at a higher tempera-

ture than the actual set point for the upper 

temperature sensor.

Alarm devices

There is a sub-alarm for the low-temper-

ature sensor and an excess-alarm for the 

high-temperature sensor.
The alarm consists of a beeper and a warn-

ing on the display. 
Alarm for high temperature: beep sound 

+ alternating display of “HtA” and actual 

temperature
Alarm for low temperature: beep sound 

+ alternating display of “LtA” and actual 

temperature
The alarm temperature depends on the set 

points.  
The beep sound can be cancelled by push-

ing a random thermostat button. Push the 

on/off button to erase the display alarm, 

first for cancelling the alarm, then again for 

restarting the compressor. 

Door alarm

When the door has been open for more 

than 2 minutes the door alarm is activated.

Light

To turn off the lights, press once 

Permanent lighting

For presentation purposes of your wine, you 

can turn the lights on permanently. Please 

press the light switch image     twice. If 

the controller is placed in the cabinet press 

twice, if the controller is placed in the kick 

plate only press once. To switch off the 

lights press on     again.

10 

Summary of Contents for 477800155























Reviews: