65E Turbo Motor Grader
Service Manual
5
-
19
Service 2.00_2013.03
Section 5
Front Axle
LH Wheel Lean Pivot Pin Removal
NOTE:
NOTE: The steering knuckle and king pin may be
removed to provide greater access, but it is not
necessary.
Step 1:
Block rear tires in both directions. Install wheel
lean lock pin, 1. Using moldboard down function, raise
front part of machine until front tires are above ground,
then support front part of draw bar with suitable
blocking, hoist, or lift.
Step 2:
Use a suitable lift to support the front axle.
Remove eight lug nuts, 1, and washers securing wheel
and tire assembly to hub. Remove wheel and tire
assembly.
Step 3:
Remove cotter pin and crown nut, 1, securing
steering cylinder socket, 2, to LH spindle, 3. Dismount
socket end of steering cylinder, 4, from LH spindle, and
support steering cylinder, allowing clearance for access
to LH wheel lean pivot pin outer plug, 5.
Step 4:
Support LH steering knuckle with suitable
blocking. Attach chain and hoist to LH hub. The
objective is to maintain equal balance between front
axle and LH steering knuckle/spindle/hub when
removing and installing wheel lean pivot pin.
Summary of Contents for 65E Turbo Motor Grader
