65E Turbo Motor Grader
Service Manual
Service 2.00_2013.03
5
-
18
Section 5
Front Axle
Step 33:
Install LH front wheel on hub, 3, with eight lug nuts, 10, and washers. Torque lug nuts to
440
-
475 Nm (325
-
350 Ib
-
ft).
Step 34:
Upon completion of RH Steering Knuckle and King Pin Installation procedure, perform front axle
toe
-
in and steering cylinder adjustments in accordance with previous FRONT AXLE, ADJUSTMENTS
procedures in this section.
RH Steering Knuckle and King Pin Installation
Step 1:
Apply previous steps 1 through 23 to RH
steering knuckle and king pin.
Step 2:
Install new nylon washer on threaded end of
steer bar RH socket link, 1. Secure steer bar RH socket
link to RH spindle, 2, with crown nut, 3. Torque crown
nut to 135.6 Nm (100 Ib
-
ft). Continue tightening crown
nut to align hole for cotter pin. Install cotter pin and bend
two ends across threaded end of socket link, and crown
nut.
Step 3:
Insure bushings are seated in wheel lean
cylinder, 1, and RH end of wheel lean bar, 2. Use pry
bar to extend and align wheel lean cylinder. Secure
wheel lean cylinder and RH end of wheel lean bar to RH
steering knuckle, 3, with bolt, 4, two washers, and nut.
Torque bolt to 542.3
-
677.9 Nm (400
-
500 Ib
-
ft).
Step 4:
Apply previous steps 28 through 34 to RH
steering knuckle and king pin.
Summary of Contents for 65E Turbo Motor Grader
