manualshive.com logo in svg

Nokia MW1122, Administrator'S Manual, Page: 105 / 129

Share
Download
Nokia MW1122 Administrator'S Manual Download Page 105

MW1122 Administrator Manual

 

E

 Copyright Nokia Networks Oy

C33902001SE_00

 5-70

Command

Set wireless LAN interface slave to Ethernet inter-
face

Description

This command makes the wireless LAN interface slave
to Ethernet interface. In this case you do not have to
assign an IP address to the wireless LAN interface. The
IP address of the Ethernet interface serves also as an
IP address to the wireless LAN interface. Note that you
must issue this command on the root level of the con-
figuration mode.

Syntax

[no] wlan slave-to-eth

Arguments

None.

Example

MW1122(conf)#wlan slave-to-eth
MW1122(conf)#

Command

Switch on/off bridging

Description

Switches of bridging at the WLAN interface.

Syntax

[no] bridging

Arguments

no

 switches bridging off.

Example

MW1122(conf-wlan)#bridging
MW1122(conf-wlan)#

Command

Switch on/off IP function in wireless LAN interface

Description

Switches on/off IP function in the Wlan interface.

Syntax

[no] ip address <ip-address> <ip-mask>

Arguments

no

 switches IP function off.

ip-address

 is the IP address you want to assign to

the wireless LAN interface.

ip-mask

 is the subnet mask.

Example

MW1122(conf-wlan)#ip address 192.168.132.12
255.255.255.0
MW1122(conf-wlan)#

Summary of Contents for MW1122


































































































































Reviews:

No comments