manualshive.com logo in svg

Nokia 7368 ISAM ONT BGW320-505, Product Manual, Page: 28 / 48

Share
Download
Nokia 7368 ISAM ONT BGW320-505 Product Manual Download Page 28

BGW320-505 unit data sheet

28

7368 ISAM ONT BGW320-505 Product Guide

3FE-47753-AAAA-TCZZA

Issue: 01

 

3.5 BGW320-505 service LEDs

The front of the BGW320-505 functions as a multi-color service LED indicator. The 

LED color and pulse rate acts as a signal to the user, which indicates the state of the 

BGW320 and the quality of its backhaul link.

Table 

5

 provides the service LED descriptions for the BGW320-505.

Table 5

BGW320-505 service LED indications

Reset button

Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the 
Reset button for 10 seconds resets the ONT to its factory defaults.

Phone
(POTS)

This connection is provided through one RJ-14 POTS port.

Power input

This connection is provided through a power cable with a Delta Electronics 
EPS48R0-16 2-pin connector. 
Use only power adapters supplied by AT&T. The use of any non-approved power 
adapter may cause damage to persons or equipment. Make sure that all power cord 
connectors are securely and completely plugged into receptacles.
Do not use the power adapter in an outdoor environment or any wet locations. Protect 
the power adapter from liquids. The conditions above may cause fire, short circuit, 
electrocution or shock injury.

USB

This connection is provided through one USB 2.0 Type A port. 
The voltage rate is 5V.

SFP

This connection is provided through a SFP+ cage that uses an optical fiber cable. One 
SFP+ connection is supported.

WPS button

Located on the front of the ONT, the Wi-Fi Protected Setup button enables and disables 
WLAN data encryption.
Supports 802.11ac, 802.11g, 802.11n, and 802.11ax.

Connection

Description

(2 of 2)

LED color

LED behavior

LED behavior description

Off

Off

Power off

White

White solid

IP service is established

White flashing (Slow)

Attempting a broadband connection; for example, the DSL is 
attempting to synchronize for the DSL.

White flashing (Fast)

Attempting an IEEE 802.1X authentication, or trying to obtain 
DHCP information.

Orange

Orange flashing

A software upgrade is in progress.
A Power-On Self-Test (POST) is in progress.

(1 of 2)

Release 06.02.00b | October 2019 | Edition 01

Summary of Contents for 7368 ISAM ONT BGW320-505

















































Reviews:

No comments