Nokia 447PRO Service Manual Download Page 20

Page: 20 / 86

447R

4.2. Service Menu

4.2.1. Access to Service Mode

Active the service mode always in 91.15 kHz/85 Hz (NCE642 ).
First switch OFF the monitor with power switch.

1) Push

button down.

2) While keeping

button down, switch ON the monitor.

3) Release

button

when the power--on indicator is illuminated.

4) Press

button.

5) Give password 7711.

6) Go to OK

6) Press

button

Select the items in the Menu with the --- or + buttons. Push

button to open Geometry, Grey

Scale, Product Information or Memory Settings. Adjust each property with navi button.

4.2.2. Geometry

Geometry submenu contain placement, size and shape adjustments.

GEOMETRY . . .

GREY SCALE . . .

PRODUCT INFORMATION . . .

MEMORY SETTINGS . . .

WIDTH PRESET

RASTER

WIDTH

HORIZONTAL CENTERING

HEIGHT
VERTICAL CENTERING

PINCUSHION

PINCUSHION BALANCE

TRAPEZOID

ORTHOGONALITY

S CORRECTION

C CORRECTION
E/W CORNER

TILT

V. MOIRE

MOIRE

00: 1280 X 1024 85 Hz

NOKIA 447PRO

85Hz

4.2.3. Grey Scale

This monitor has sexen preset tints. With tint numbers smaller than 4 the picture becomes reddish

and with tint numbers greater than 4 the picture turns blue.

Tint no

Colour Temperature 5000K 6000K 6500K 7000K 8000K 9300K 10000K

The grey scale adjustment affects directly tint number 6 (9300K) only. Other tints are derived auto-

matically from 9300K colour temperature.

GEOMETRY . . .

GREY SCALE . . .

PRODUCT INFORMATION . . .

MEMORY SETTINGS . . .

EXIT MENU

CONTRAST

MIN CONTRAST

MAX CONTRAST

BRIGHTNESS

G2
RED BLACK LEVEL

GREEN BLACK LEVEL

BLUE BLACK LEVEL

RED AMP.

GREEN AMP.

BLUE AMP.

00: 1280X1024 85Hz

GEOMETRY . . .

GREY SCALE . . .

PRODUCT INFORMATION . . .

MEMORY SETTINGS . . .

EXIT MENU

MODEL:

NOKIA 447PRO

SERIAL NUMBER

9919000398

POWER ON HOURS

STAND--- BY HOURS

SUSPEND HOURS

ACTIVE--- OFF HOURS

FIRMWARE

0.28

00: 1280X1024 85 Hz

GEOMETRY . . .

GREY SCALE . . .

PRODUCT INFORMATION . . .

MEMORY SETTINGS . . .

EXIT MENU

TYPE :

BRAND

CRT:

DDC

EXT. (24LC21)

AUDIO :

INITIALIZE EEPROM

00: 1280X1024 85 Hz

NOKIA 447PRO

85Hz

NOKIA 447PRO

85Hz

NOKIA 447PRO

85Hz

Summary of Contents for 447PRO























































































Search results

Summary of Contents for 447PRO

Reviews:

Related manuals for 447PRO

Brands by name

Popular brands

Nokia 447PRO, Service Manual

Search results

Summary of Contents for 447PRO

Reviews:

Related manuals for 447PRO

Brands by name

Popular brands