NodeTalks G-Tag 100 User Manual Download Page 5

NDTUM-GTAG-EN  REV2.0

©  NodeTalks  Corp.  All  rights  reserved.

.

5

3. User  Precautions

[  WARNING  ]

DO  NOT  OPEN  OR  REPLACE  BATTERY  WHEN  EXPLOSIVE  ATMOSPHERE  IS  PRESENT. 

POTENTIAL  ELECTROSTATIC  CHARGING  HAZARD 

CLEANING  SHALL  BE  DONE  WITH 

– 

A  DAMP  CLOTH.

            Warning

When  operating  the  gas  detector  for  the  first  time,  or  turning  it  on 

again  after  not  using  it  for  a  long  period  of  time,  it  takes  a  few 

minutes  for  stabilization  until  it  indicates  accurate  results.  (turn  on  the 

product  in  the  clean  atmospheric  environment  without  harmful  gas)

Do  not  use  this  product  for  gas  measurement  or  as  gas  analyzer  since 

it  is  a  detection  and  alarm  device.  In  addition,  since  it  is  a  portable 

device,  we  are  not  responsible  for  any  problem  that  may  occur  if  it  is 

used  as  a  fixed  or  mobile  device. 

Arbitrary  dissembling  of  products  or  replacement  of  parts  may  cause 

detrimental  damage  on  the  products.  Direct  touch  of  internal  circuit 

may  cause  static  electricity,  resulting  in  circuit  damage.  Contact 

NodeTalks    Corp..  if  the  sensor  or  the  battery  require  replacement. 

Do  not  power  off  the  products(for  a  long  time)  since  this  product 

carries  out  automatic  calibration  of  the  gas  sensor.  It  is  recommended 

to  keep  the  gas  detector  in  a  safe  place  with  the  power  on  when  not 

in  use. 

Improper  handling  or  use  of  the  product  may  cause  reduction  of  the 

service  life  or  inaccurate  gas  detection. 

(Example  of  improper  handling: 

storage  near  hot,  flammable  or  toxic  substance,  soaking  in  the  water  or 

impact  on  the  product  case  or  gas  measurement  hole,  etc.)

This  product  has  been  manufactured  without  its  display  and  you  can 

check  the  detection  results  of  oxygen  and  toxic  gas  using 

“Smart  Gas 

Sniffer”, 

the  dedicated  Bluetooth  application(hereinafter  dedicated  app) 

at  your  smartphone.  You  can  download  the  dedicated  app  at  Google 

PlayStore  or  Apple  AppStore  for  free.  Be  sure  to  download  it  in  a  safe 

place(explosion-proof  area). 

This  product  operates  as  a  stand-alone  gas  alarm  and  gives  an  alarm 

according  to  situation  in  case  of  gas  deficiency  or  gas  leakage.  Be  sure 

to  keep  the  dedicated  app  of  the  smartphone  running  when 

wearing(using)  this  product  in  order  to  grasp  the  situation  quickly  in 

case  of  emergency  and  to  automatically  respond  to  it. 

Some  functions  such  as  sending  situation  message  may  be  restricted  in 

the  shielded  places  where  incoming  and  outgoing  call  of  smartphone  is 

not  possible. 

Various  functions  implemented  through  the  smartphone  may  be  lost  if 

distance  between  this  product  and  smartphone  is  so  far  that  Bluetooth 

signal  cannot  reach.  Use  it  only  within  the  communication  distance 

between  the  devices,  and  check  the  normal  operation  of  app.   

Summary of Contents for G-Tag 100





























Reviews: