background image

 

19 

8. 

BATTERY CHARGING AND REPLACEMENT 

 

O

nly qualified personnel are allowed to service or charge the batteries. The 

instructions of this handbook must be observed. 

 

PSE12BD is lead acid battery, PSE12ND is lithium battery 

 

Recycling  of  batteries  undergoes  national  regulations.  Please  follow  these 
regulations.   

 

By handling batteries, open fire is prohibited! 

 

In  the  area  of  battery  charging  neither  burning  materials  nor  burning  liquids  are 
allowed. Smoking is prohibited and the area must be ventilated. 

 

Park the truck securely before starting charging or installing/changing the batteries 

 

Before finishing the maintenance work, make sure, that all cables are connected               
correctly and that there are no disturbing towards other components of the truck. 

 

PSE12BD is equipped with the following lead-acid battery: 
2x12V / 85Ah, 2x27kg;        option: 2x12V / 106Ah

2x34kg 

PSE12ND is equipped with the following lithium battery: 
24V / 60Ah, 19kg 

 

I

T  IS  ONLY ALLOWED TO  USE  LEAD ACID  BATTERY  FOR  PSE12BD.  IT  IS  ONLY 

ALLOWED TO USE LITHIUM BATTERY FOR PSE12ND. 
PLEASE  CONSIDER  THE  MAXIMUM  OPERATING  TEMPERATURE  OF  THE 
BATTERIES. 
 

a.

 

Safety Instructions (

lithium battery)

 

Failure to follow the below requirements may cause damage to your property, cause injuries or death. 

Measures to prevent ignition 

 

It is forbidden to work at temperatures over 60 

 

It is forbidden to place it beside heat sources, such as stoves, fireplaces, etc. 

 

Direct sunlight must be avoided. 

 

It is forbidden to place batteries near inflammable and explosive substances. 

Measures to prevent explosion 

 

Do not hit the battery, no impacts are allowed. 

 

Exclude penetration of objects through battery case or damages to battery case 

 

DO not throw products into the fire or water. 

Measures to prevent electric leakage 

 

Do not disassemble. 

 

Do not contact by wet hands. 

 

Do not expose it to moisture or liquids. 

 

Do not place batteries in a place of easy access by children or animals. 

Measures to preventing damage to battery systems 

 

It is forbidden to contact liquids or corrosive chemicals. 

 

Do not expose batteries to high temperature and/or high pressure. 

 

No trampling, disassembly or smashing. 

 

Do not attempt charging from discharge terminals and discharging from charging terminals. 

Summary of Contents for PSE12BD

































Reviews: