background image

 

20 

 

check the wiring of the J2 of pedal. 

3. Check the wiring of J3 to J8. 

Drive open         

Drive  motor  wire  connection 

open

 

Check the drive motor and related wiring. 

Drive overcurr   

Drive 

motor  current  is  too 

high. 

Check the drive motor and electromagnetic brake. 

Brake open       

Electromagnetic brake open 

circuit 

Check  the  electromagnetic  brake  position  and  coil 

resistance. 

No LCD display 

LCD display is broken. 

Replace the panel. 

No  battery  charge 

notches  and  F6B6 

on LCD display,  and 

voltage  displays  0 

after booting 

1.  The  controller  is  not 

powered on. 

1.  Check  if  there  is  voltage  on  the  5th  pin  of  J2  of  the 

controller; 

2. The signal cable between 

the controller and the panel 

is not connected. 

2.  Check  whether  the  connection  cable  between  J3  of 

controller    and J8 of panel is connected. 

LCD  display  voltage 

is 0 after booting 

Communication 

between 

the  drive  circuit  of  the 

controller  and  control  panel 

is not established. 

Check  whether  the  5th  and  6th  pins of  the  controller  J3 

are connected to the J8 of panel. 

The  LCD  does  not 

display  the  battery 

charge notches  after 

power on 

Communication 

between 

the  vacuum  circuit  of  the 

controller  and  control  panel 

is not established. 

1.  Check  if  the  3rd  and  4th  pins  of  controller  J3  are 

connected to the panel. 

2. Turn off the machine and restart. 

 

CAUTION! 

When  there  is  a  fault  alarm,  please  turn  off  the  power  and  wait  5  seconds 

before restarting. 

 

 

Summary of Contents for NR530
























Reviews: