background image

www.nkrowing.com.au

10

LAY OUT THE PARTS OF YOUR SYSTEM

Uncoil the wiring harness and lay it out in the shell. If you are installing your COX BOX in a sectional 
shell, the harness should be equipped with a plug/receptacle pair which should be within a foot of 
the sectional bulkheads.

NSTALL THE STROKE SENSOR (CoxBox system only)

1. 

Refer to FIGS 1a, 1b. Note the position of the sensor – it should be close to the center of the
seat travel and it MUST be perpendicular to the length of the shell.
It is not necessary for the sensor and magnets to be centered between the rails as shown
in Figure 1a. They may be positioned off center as shown in Fig 1b. It is essential however
that the magnet passes directly over the sensor.

INSTALLING YOUR SYSTEM

Check that you received everything required. If you purchased a complete CoxBox system you should 
have received the following items:

Carrying 

bag 

.......................................................................................................(1)

CoxBox (or Cox Vox) control unit  ...............................................................(1)

microphone.........................................................................................................(1)

charger 

..................................................................................................................(1)

speakers ............................................................................... (as ordered  2 or 3)

mounting 

cup 

....................................................................................................(1)

harness, with sensor installed.......................................................................(1)

“Do’s & Don’ts” card ..........................................................................................(1)

hardware pack with magnet ........................................................................(1)

NOTE: The double-sided “VHB” tape provided for mounting is epoxy based and requires 12 hours of cure 

time. Do not get this tape wet while curing for best results.

Summary of Contents for CoxBox

















Reviews: