NJD Electronics SPECTRE User Manual Download Page 15

Page: 15 / 16

Technical Specification.

Dimensions:

250mm x 250mm x 245mm

Weight:

5.2kg

Lamps:

3 x A1/244 (230V 500W)

Lamp Life:

50 hours at 240V AC

100 hours at 230V AC

Colours:

Red:

(0.700,0.296)

Green:

(0.246,0.686)

Blue:

(0.128,0.153)

and all intermediate shades

Power Supply:

230V AC 50Hz

Power:

1500W (all lamps illuminated)

Current:

6.5A rms. (all lamps illuminated)

Power factor:

cos

= 1.000

(The Spectre is a resistive load)

Switch-on Surge:

30 Amps for 60ms

(all three lamps switched at the same

time, 0.4

mains source impedance)

Beam spread:

56° (to 50% brightness).

(1m wide at 1m distance)

Beam intensity:

2200 candela per channel.

DMX input/output:

complies with

DMX512 (1990) 4µsec protocol

Connectors:

5-pin XLR

Data+:

Pin 3

Data-:

Pin 2

Earth:

Pin 1

+12V supply: Pin 5

Analogue input voltage:

0-10V

Analogue input impedance:

44k

Analogue connector:

7-pin DIN

Channel 1:

pin 3

Channel 2:

pin 5

Channel 3:

pin 4

Channel 4:

pin 1

0V (ground): pin 2

Standards

The Spectre complies with Electrical Safety Standard EN60598

Parts 1 and 2-17 (1997), and Electromagnetic Compatibility

Standard EN55015.

User Guide

Spectre

-Page 15-

Summary of Contents for SPECTRE

















Search results

Summary of Contents for SPECTRE

Reviews:

Related manuals for SPECTRE

Brands by name

Popular brands

NJD Electronics SPECTRE, User Manual

Search results

Summary of Contents for SPECTRE

Reviews:

Related manuals for SPECTRE

Brands by name

Popular brands