£
Turn the Right rotary knob to “Care”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care Rinse”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Rinse frother”. Now press the Right rotary knob.
The messages “Hose to spout” and “and into drip tray” will toggle alternately on your display.
£
Connect the hose to the vertically-adjustable spout (Fig 7).
£
Put the free end of the hose into the hole at the back of the drip tray on the right (Fig 10).
£
Place a sufficiently large vessel (with a capacity of at least 0.5 litres) under the spout.
£
Now press the Right rotary knob.
“Frother is rinsing” now appears on the display. Your machine will now begin the automatic rinsing
process. The rinsing process takes approx. 20 seconds.
Once the rinsing cycle is complete, the heating cycle will begin and your machine is once again ready
for operation.
5.2 Rinsing the spout
The spout should be rinsed out regularly. Proceed as follows:
£
Turn the Right rotary knob to “Setting”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care Rinse”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Rinse Spout”. Now press the Right rotary knob.
The message “System is rinsing” will appear on your display.
Once the rinsing cycle is complete, the heating cycle will begin and your machine is once again ready
for operation.
5.3 Cleaning the frothing device
WARNING! Once activated, the programme may not be interrupted!
We recommend that the frothing device be cleaned regularly. Cleaning MUST be carried out, however,
when instructions to that effect appear on your display. Proceed as follows:
£
Turn the Right rotary knob to “Setting”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care Clean”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Clean frother”. Now press the Right rotary knob.
The messages “Hose to spout” and “end into cleaner” will toggle alternately on your display.
£
Connect the hose to the vertically-adjustable spout (Fig 7).
£
Dissolve a little of the cleaning fluid (available as an accessory, see Point 9) in a container with
water to make a solution of at least 0.3l. The ratio of cleaning fluid to water is given in the manu-
facturer’s instructions.
£
Put the end of the hose into the cleaning solution.
£
Place a sufficiently large vessel (with a capacity of at least 0.5 litres) under the spout.
£
Now press the Right rotary knob.
Your machine will now begin the cleaning process. The “Cleaning Activated” message appears on your
display.
After a few moments, the messages “Hose to spout” and “and into drip tray” will toggle alternately on
your display.
£
Connect the hose to the vertically-adjustable spout (Fig 7). Put the free end of the hose into the
hole at the back of the drip tray on the right. Now press the Right rotary knob.
The “Cleaning Activated” message appears on your display.
Once the cleaning cycle is over, the “Empty trays” message appears on the display.
£
Empty the drip and used coffee trays (Figs 1/N and 1/O), clean and replace.
The heating cycle will now begin and the machine will again be ready for use.
5.4 Cleaning the system
Note: When the machine needs cleaning, instructions on how to proceed will be shown on the display. In
order not to prejudice any possible warranty claims, please follow these instructions carefully.
WARNING! Look out for the “Please clean” message appearing on the display. You may continue to
obtain drinks from your machine. Once you have started the cleaning programme, however, it must not
be interrupted. The machine will tell you when to put in a cleaning tablet.
£
Turn the Right rotary knob to “Setting”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care Clean”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Clean System”. Now press the Right rotary knob.
The “Empty trays” message will appear on the display.
£
Remove the drip and used coffee trays (Figs 1/N and 1/O) and empty them.
£
If necessary, fill the water container with fresh water, then replace the water container, drip tray
and used coffee tray.
The machine will now rinse twice.
The “Cleaning tablet in” and “Powder Chute” messages will now toggle alternately on the display.
£
Place a sufficiently large vessel (with a capacity of at least 0.5 litres) under the spout (Fig 1/E).
£
Open the lid to the coffee powder chute (Fig 1/M).
£
Put the cleaning tablet into the powder chute and close the lid.
The “Start Cleaning” message appears on your display.
£
Now press the Right rotary knob.
Your machine will now begin the cleaning process. The message “System is cleaning” will appear on
your display. The cleaning process is automatic and lasts approx. 10 minutes.
Once the cleaning cycle is over, the “Empty trays” message appears on the display.
£
Empty the drip and coffee dregs trays (Figs 1/N and 1/O), clean and replace.
£
If necessary, fill the water container with fresh water.
The heating cycle will now begin and the machine will again be ready for use.
5.5 Descaling the system
When the machine needs de-scaling, the “Please descale” message will appear in the display.
You can, however, start the descaling programme manually at any time.
WARNING! Please follow the descaling instructions precisely and in the order they are given! You may
continue to obtain drinks from your machine. We recommend, however, that you start the de-scaling
programme as soon as possible. Failure to descale your machine may exempt any claims under war-
ranty.
WARNING! Once activated, the descaling programme must not be interrupted! Only use proprietary
solvents specially recommended for use in coffee machines. Do not attempt to use vinegar or any
vinegar-based descaling agents.
WARNING! The filter must be removed from the water container prior to starting the descaling programme.
£
Turn the Right rotary knob to “Setting”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care”. Now press the Right rotary knob.
£
Turn the Right rotary knob to “Care Descale”. Now press the Right rotary knob.
The “Empty trays” message will appear on the display.
32
33
GB
GB
5. Care and maintenance
5. Care and maintenance
