background image

Manual: EV-DPH Manual 000027  (Changes are subject to DCRN)

8

• Ref No: NISM/EV-DPH/01 •  May 2010 •  Issue: 1

•  Evolution  •  EV-DPH  •  analogue addressable 

photoelectric / heat sensor 

The 7 segment LED distinguishes the 
Customer Code, Type and Address by the dot 
position in the LED.

The information displayed by the 7 segment 
LED cycles every second and stops whilst 
displaying the [address] at the end of the 
second cycle. Pressing any key at any time during 
the information collection cycle, forces the 
EV-AD2 to display the address, and await new 
address selection.

6. +100, +10, +1 keys are used to select the 

new address.

7. Press the [Set] key

a) The buzzer sounds, and all LED’s are 

turned off. The EV-AD2 then starts 
transmitting to the detector.

b) Do not remove the detector.

8. The 7 segment LED shows the new address and 

“complete” LED lights. If an unsupported or 
defective device is connected the buzzer sounds ,
ERROR LED is lit and the 7 segment LED reads 
ERROR CODE. 

9. To continue changing the address for another 

detector, change the detector and then repeat 
from step 3. To finish changing addresses, 
turn the POWER SW off.

1

Stand by mode

EV-AD2 will switch to STAND-BY MODE to save
battery power if there is no key operation for
more than one minute after finishing changing
device addresses. During the STAND-BY MODE, 7
segment LED is blank. Power LED is lit.

To return EV-AD2 from STAND-BY MODE press
any key.

2

Instruction

1. EV-AD2 requires two 9v PP3 batteries.

a) Before inserting the batteries, confirm 

the EV-AD2 is switched off and check 
polarity of battery, or damage 
could result.

2. Turn the power switch ON.

a) For one second, all LED’s are lit and the 

buzzer sounds.

3. Plug the device onto the base.

4. Press the [Search] Key

a) Buzzer sounds, then the EV-AD2 starts 

transmitting to the detector.

b) Do not remove the detector when 

transmitting, or damage could result.

5. The 7 segment LED reads [Customer code], 

[Type of detector], [Address] in turn.

a) The buzzer sounds, ERROR LED lights 

and the 7 segment LED displays an 
ERROR CODE when an unsupported 
or defective device is connected.

0.01

12.3

003.

Customer Code

Type of detector

Address

Section 9 - ADDRESS SETTING 

(EV-AD2)

(Note - Dot position)

Summary of Contents for EV-DPH











Reviews: