9
10
ninjacoffeebar.com
1-877-646-5288
Assembly
1
Place the brewer on a dry, clean and level surface.
2
To easily fill the water reservoir, use the hand grips to lift
it straight up off the brewer.
(Fig. 5)
The water reservoir
lid flips open for easy filling, and the entire lid is easily
removable for quick cleaning. Add fresh, filtered water at
or above the minimum fill line for your desired beverage
size
(Fig. 6)
, then return the water reservoir to the brewer
and lock into place.
(Fig. 7)
Do not fill water reservoir
with any other liquids such as brewed coffee, carbonated
beverages, etc. as other liquids may damage your brewer.
TO SET THE CLOCK
1
Plug the power cord into an electrical outlet. The clock
will flash on the control panel to indicate that the time
has not been set.
(Fig. 1)
2
Press the H (hour) or M (minute) button until you reach
the current time. The AM or PM indicator will illuminate
on the left side of the display as you are setting the
time.
(Fig. 2)
3
After 5 seconds the clock will stop flashing and the
clock will be set.
NOTE:
If the clock stops flashing and does not display
the correct time of day, pressing the H (hour) or the M
(minute) button at any time will cause the clock to flash
again. You can now re-program the correct time of day
by following the steps above.
NOTE:
If you unplug the brewer or in the event of an
extended power loss, you will need to reset the clock
the next time the brewer is plugged in.
TO SET THE DELAY BREW TIME
1
Press Delay Brew. The Delay Brew button will illuminate
and the clock will begin to flash “12:00” or the last
delay brew time that was set.
(Fig. 3)
2
While the clock is flashing, press the H (hour) or M
(minute) button to set the time that you would like
the delay brew to begin. The AM or PM indicator will
illuminate on the left side of the display as you are
setting the desired time.
Setting the Clock & Delay Brew
Fig. 3
Fig. 4
Fig. 2
Fig. 1
3
Once the proper time has been set, select the size of
the vessel that you would like to brew.
4
Select the Brew Type that you desire from the 5 flashing
buttons. The selected brew type will be lit.
(Fig. 4)
5
Once the time, brew size, and brew type have been set, allow
the Delay Brew to flash and lock in or press the Delay Brew
button to activate the Delay Brew. When the Delay Brew is
activated, the light on the Delay Brew button will illuminate
and an audible signal will play to verify the Delay Brew is set.
6
The Delay Brew time is now set and your Ninja
Coffee Bar
®
will automatically brew at the time you programmed.
NOTE:
To deactivate the Delay Brew cycle, press the Delay
Brew button once more and the light on the Delay Brew
button will turn off. Any change to the selected brew size or
starting any other brew will cancel the programmed
Delay Brew.
7
Place the appropriate-sized vessel under brew basket for the
selected size.
IMPORTANT:
Make sure the Drip Stop is in the open position.
3
Slide brew basket out
(Fig. 8)
and lift both the
permanent filter and permanent filter carrier from the
brew basket to remove.
(Fig. 9)
To reinsert, set the
permanent filter and permanent filter carrier back into
the brew basket.
(Fig. 10)
When cleaning, you can
remove the permanent filter from the brew basket.
4
Once the filter is in place, slide the brew basket all the
way in until you hear a slight click.
Fig. 5
Fig. 8
Fig. 6
Fig. 9
Fig. 7
Fig. 10
Go to ninjacoffeebar.com for more
information and how-to videos.