9
10
www.ninjakitchen.com
1.877.646.5288
10
Review warning and caution statements on page 8
before proceeding to Step 11.
11
Select the speed that best suits your needs.
(Fig. 6)
NOTE:
Pulse ingredients for even chopping by pressing
the PULSE button in short intervals.
12
If the ingredients stick to the side of the pitcher, stop
the appliance by pressing the Power button ( ) and
wait for the Stacked Blade Assembly to stop turning.
Then remove the lid by pressing the release button,
lifting the handle, and pulling straight up.
(Fig. 7)
Use a
rubber spatula to dislodge the ingredients, replace the
lid, and continue processing.
13
When you have reached your desired consistency, stop
the appliance by pressing the Power button ( ) and
wait for the Stacked Blade Assembly to stop turning.
(Fig. 7)
WARNING: Never insert your hands in the pitcher
as the Stacked Blade Assembly is sharp. Always
use a spatula to dislodge ingredients that has
stuck to the sides of the pitcher.
14
Turn the pitcher counterclockwise and then lift it off the
base.
(Fig. 8)
Fig. 7
USE
REMOVAL
Fig. 6
Fig. 8
15
Open the pour spout cap and use the spout to empty
contents.
16
For thicker consistencies, first remove the lid by
pressing the release button and pulling the lid handle
up to a 90 degree angle to lift lid off the pitcher. Then,
carefully remove the Stacked Blade Assembly by the
top of the shaft. Place Stacked Blade Assembly away
from the work area to avoid accidental contact. Finally,
empty contents from the pitcher.
17
Make sure the unit is unplugged when not in use.
Assembly and Use of the Pitcher - cont.
1
Review warning and caution statements above before
proceeding to Step 2.
2
Place the motor base on a clean, dry, level surface such
as a counter or table.
3
Add ingredients to the Nutri Ninja Cup.
NOTE: Do not overfill! To avoid spilling, do not
add ingredients past the “Max” fill line.
4
Place the Nutri Ninja Blade Assembly onto the cup and
turn it clockwise until you have a good seal.
(Fig. 1)
5
Turn the Nutri Ninja Cup upside down and place it onto
the motor base, aligning the tabs on the cup with the
motor base. Turn clockwise until you hear a click, then
the unit is ready for use.
(Fig. 2)
6
Plug the power cord into an electrical outlet and press
the Power button ( ).
7
Press down on the PULSE button in short intervals to
pulse.
(Fig. 3)
Press the Nutri Ninja
button to activate
the run cycle. The blender will stop after 60 seconds. To
stop at any time during the cycle, press the Nutri Ninja
button a second time or press the Power button ( ).
Fig. 1
Fig. 2
Assembly and Use of the Nutri Ninja
®
Cup
Fig. 3
Fig. 4
Fig. 5
Fig. 6
ASSEMBLY
PULSE
REMOVAL
8
Once you have reached your desired consistency, stop
the appliance by pressing the Power button and wait
for the blade to stop turning. Turn the Nutri Ninja Cup
counterclockwise and pull straight up to remove.
(Fig. 4, Fig. 5)
9
Turn the cup upright and remove the Nutri Ninja Blade
Assembly by twisting blade assembly counterclockwise.
(Fig. 6)
10
Do not store blended contents with the Nutri Ninja
Blade Assembly attached.
11
Place the To-Go Lid on the Nutri Ninja cup and twist
clockwise to seal.
12
Be sure to store the Nutri Ninja Blade Assembly
attached to an empty cup when not in use.
13
Make sure the motor base is unplugged when not in
use.
WARNING: Handle the Nutri Ninja Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the Nutri Ninja Cup to be
damaged or to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, as doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
CAUTION: Remove the Nutri Ninja Blade Assembly from the Nutri Ninja Cup upon completion of blending.
Do not store ingredients before or after blending them in the cup with the blade assembly attached. Some
foods may contain active ingredients or release gases that will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury.
IMPORTANT: Make sure the motor base is plugged in for use.
