background image

3

1)

 Options / model variants

NEPTUNE 5 SB FA 

CAUTION!
High-pressure water jets can 
be dangerous if misused. The 
jet must not be directed at 
persons, animals, live electri-
cal equipment or the cleaner 
itself.

Wear appropriate protective 
clothing and eye protection.

Do not direct the jet towards 
yourself or towards other per-
sons in order to clean clothes 
or footwear. 

During operation of the cleaner, 
recoil forces are produced at the 
gunvalve and spray lance and, 
when the spray lance is held at 
an angle, a torque is also cre-
ated. The gunvalve and spray 
lancemust therefore be held 
fi rmly in both hands.

Do not use the cleaner when 
other people without protec-
tive clothing are in the working 
area.

Check that cleaning will not 
result in dangerous substances 
(e.g. asbestos, oil) being washed 
off the object to be cleaned and 
harming the environment.

Do not clean delicate par ts 
made of rubber, fabric, etc. with 
the 0° jet.  Keep some distance 
between high pressure nozzle 
and surface in order to prevent 
the surface from damage.
Do not use the high-pressure 
hose for lifting loads.

NOTE

!

The maximum permissible work-
ing pressure and temperature 
are printed on the high-pressure 
hose.

Do not use the cleaner if the 
power cord or high-pressure 
hose is damaged.

Ensure adequate air circulation. 
Do not cover the cleaner or oper-
ate it in inadequately ventilated 
rooms!

Store the cleaner where 
it will not be exposed to 
frost  or use antifreeze 

liquid!

Never operate the cleaner with-
out water. Even brief shortages 
of water result in severe damage 
to the pump seals.

Water connection

This high pressure 

washer/cleaner is 
only allowed to be 
connected with the 
drinking water

mains, when an appropriate 
backflow preventer has been 
installed, Type BA according to 
EN 1717.  If the back flow pre-
venter hasn’t been supplied, 
one can be ordered from your 
dealer. The length of the hose 
between the backflow preventer 
and the high pressure washer 
must be at least 12 metres (min 
diameter 3/4 inch) to absorb 
possible pressure peaks. Op-
eration by suction (for example 
from a rainwater vessel) is car-
ried out without backflow pre-
venter. Contact your dealer for 
suction set recommendations.
As soon as water has flown 
through the BA valve, this water 
is not considered to be drinking 
water any more.

Operation

Keep cabinet and service door 
closed during operation.

CAUTION!
Unsuitable extension cords 
can represent a source of 
danger. Always unwind cord 
from the reels completely to 
prevent the power cord over-
heating.

Connectors and couplings of 
extension cords must be water-
tight.

Extension cords are not recom-
mended, however if necessaray 
refer to the following recommen-
dations:

Cord length
m

Cross section

up to16 A

up to 25 A

up to 20 m 
(US: 30 ft)
(US: 50 ft)
(US: 75 ft)

ø1.5mm²
14 gauge
12 gauge
10 gauge

ø2.5mm²
12 gauge
10 gauge
not recom-
mended

20 to 50 m

ø2.5mm²

ø4.0mm²

Do not damage the power cord 
(e.g. by driving over it, pulling or 
crushing it).
Disconnect the power cord by 
grasping the plug only (do not pull 
or tug the power cord).

CAUTION!

Unsuitable fuels (e.g. gasoline) 
must not be used as they can 
explode and catch fi re.

Use clean fuel only, free of mois-
ture and contamination. Contact 
your dealer for fuel source and 
type recommendations.

If the machine is to be operated at 
fuel stations or in other potentially 
hazardous areas, the machine 
may only be employed outside 
the hazard areas defi ned in the 
German  „Technical Guidelines 
for Infl ammable Fluids“ applica-
ble at the point of use due to the 
potential explosion hazard posed 
by the burner.

If the machine is to be operated 
indoors, the local building regu-
lations must be observed for the 
discharge of the exhaust fumes 
into the atmosphere. Ensure an 
adequate supply of fresh air. 

If the machine is to be con-
nected to a fl ue gas stack, then 
local building regulations must be 
observed. We will be glad to pro-
vide tips for connection systems, 
on request.

CAUTION!

Beware of hot water and 
steam discharge up to 
150

0

C when operating in 

steam stage

.

CAUTION!

Do not touch or cover the 
exhaust. Risk of burns 
and fi re.

Summary of Contents for NEPTUNE 5 SB FA

















































Reviews: