Nilfisk-ALTO NEPTUNE 3 Original Instructions Manual Download Page 5

5

1)

 Options / model variants

Original instructions

NEPTUNE 3

appliance into service, always 
check the power supply cord 
and the other important parts of 
the appliance, such as the high-
pressure hose and the spray 
gun. Do not operate the appli-
ance if any of these parts are 
damaged.

Set up the appliance such that 
the mains connector is readily 
accessible.

Regularly check whether the 
power cord is damaged or 
shows signs of ageing. Use 
the high-pressure cleaner only 
when the mains power lead is 
in a safe condition. 

If the power supply cord is 
damaged, to avoid hazards, 
this must be replaced either by 
the manufacturer or through his 
customer service or a similarly 
qualified person.

CAUTION!

Unsuitable extension leads can 
represent a source of danger. 
Always unwind cord from the 
reels completely to prevent the 
power cord overheating.

WARNING

Inadequate extension cables 
can be dangerous. If an exten-
sion cable is used, it shall be 
suitable for outdoor use, and 
the connection has to be kept 
dry and off the ground.
Nilfisk recommends use of an 
extension cable drum when ca-
ble extension is needed which 
keeps the socket at least 60 
mm above the ground.

Connectors and couplings of 
power supply cords and exten-
sion leads must be watertight.

When using an extension lead, 
check the minimum cross-sec-
tions of the cable:

Cable length
m

Cross section

<16 A

<25 A

up to 20 m

ø1.5mm²

ø2.5mm²

20 to 50 m

ø2.5mm²

ø4.0mm²

Check the rated voltage of the 

high-pressure cleaner before 
connecting it to the mains pow-
er supply. Ensure that the volt-
age shown on the rating plate 
corresponds to the voltage of 
the local mains power supply.

It is important that the electrical 
connection for this appliance 
has been installed by an elec-
trician and in compliance with 
IEC 60364 and the country-
specific regulations.

We recommend that the electri-
cal connection to this appliance 
should incorporate 
–  either a fault current circuit 

breaker, which cuts off the 
mains voltage if the fault 
current exceeds 30 mA for 
30 ms,

–  or an earth resistance me-

ter.

Check that cleaning will not 
result in dangerous substances 
(e.g. asbestos, oil) being 
washed off the object to be 
cleaned and harming the envi-
ronment.

Do not clean delicate parts 
made of rubber, fabric, etc. with 
the 0° jet.  Keep some distance 
between high pressure nozzle 
and surface in order to prevent 
the surface from damage.

Do not use the high-pressure 
hose for lifting loads.

The maximum permissible 
working pressure and tempera-
ture are printed on the high-
pressure hose.

 

Store the cleaner 
where it will not be 
exposed to frost!

Never operate the cleaner with-
out water. Even brief shortages 
of water result in severe dam-
age to the pump seals.

Operation

Keep cabinet and service door 
closed during operation.
Do not damage the mains 

power lead (e.g. by driving over 
it, pulling or crushing it).

Disconnect the power cord by 
pulling the plug only (do not pull 
or tug the power cord).

IMPORTANT!

This appliance has been de-
vised for use with cleansing 
agents that are supplied and 
recommended by the manufac-
turer. The use of other cleans-
ing agents or chemicals can 
impair the safety of the appli-
ance.

CAUTION!

The appliance is intended to 
be used with heating oil EL or 
diesel oil.

 

Unsuitable fuels (e.g. 

petrol) must not be used as 
they can represent a source of 
danger.

If the machine is to be oper-
ated at fuel stations or in other 
potentially hazardous areas, the 
machine may only be employed 
outside the hazard areas de-
fined in the German  „Techni-
cal Guidelines for Inflammable 
Fluids“ applicable at the point 
of use due to the potential ex-
plosion hazard posed by the 
burner.

When setting up the appliance 
indoors, always ensure suitable 
ventilation and that the exhaust 
gases are expelled in a suitable 
way.

If the machine is to be con-
nected to a flue gas stack, then 
local building regulations must 
be observed. We will be glad to 
provide tips for connection sys-
tems, on request.

CAUTION!

Do not touch or cover the ex-
haust. Risk of burns and fire.

Electrical equipment

Summary of Contents for NEPTUNE 3























Reviews: