Nilfisk-Advance SR 1800S 2WD, User Manual

Page: 75 / 118

USER MANUAL ENGLISH
SR 1800S D 2WD 33014097(2)2006-12 A 21
MAIN BROOM HEIGHT CHECK AND
ADJUSTMENT
Check the main broom print according to the following
procedure:
Drive the machine on a level ground.
While keeping the machine stationary, lower the main
broom and allow it to turn for a few seconds.
Stop and lift the main broom, then move the machine.
Check that the main broom print is as shown in the fi gure
(Fig. O).
If the print is not within specifi cations, adjust the main
broom height by using the screw (1, Fig. Q).
MAIN BROOM REPLACEMENT
NOTE
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
CAUTION!
It is advisable to wear protective gloves when
replacing the main broom because there can be
sharp debris between the bristles.
Prepare the machine as shown in After Using the
Machine paragraph.
Remove the right lower lid (50, Fig. F).
Remove three wing nuts (1, Fig. R).
Remove the dust panel fastening plate (2, Fig. R).
Move the dust panel (3, Fig. R).
Remove the safety clip (1, Fig. S).
Remove the main broom support fl ange (2, Fig. S).
Remove the main broom (3, Fig. S) and replace it.
Perform steps 2, 3, 4, 5, 6 and 7 in the reverse order.
RIGHT DUST PANEL REPLACEMENT
Prepare the machine as shown in After Using the
Machine paragraph.
Start the engine as shown in the relevant paragraph.
Turn the engine throttle lever (19, Fig. B - 29, Fig. C) to
“MAX”.
Lift the hopper (2, Fig. F) by pushing and holding the
right distributor lever (12, Fig. B - 31, Fig. C).
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Install the support rods (4, Fig. F).
Remove the right lower lid (50, Fig. F).
Remove three wing nuts (1, Fig. R).
Remove the dust panel fastening plate (2, Fig. R).
Remove four inner screws (1, Fig. T).
Remove the dust panel fastening plate (2, Fig. T).
Remove the dust panel (3, Fig. R) and replace it.
Perform steps 2, 3, 4, 5, 6, 7, 8, 9, 10 and 11 in the
reverse order.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
7.
8.
9.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
LEFT DUST PANEL REPLACEMENT
Prepare the machine as shown in After Using the
Machine paragraph.
Start the engine as shown in the relevant paragraph.
Turn the engine throttle lever (19, Fig. B - 29, Fig. C) to
“MAX”.
Lift the hopper (2, Fig. F) by pushing and holding the
right distributor lever (12, Fig. B - 31, Fig. C).
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Install the support rods (4, Fig. F).
Remove the left lower lid (51, Fig. F).
Remove three wing nuts (1, Fig. U).
Remove the thrust spring (3, Fig. U).
Remove the dust panel fastening plate (2, Fig. U).
Remove four inner screws (1, Fig. V).
Remove the dust panel fastening plate (2, Fig. V).
Remove the dust panel (4, Fig. U) and replace it.
Perform steps 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 and 12 in the
reverse order.
REAR DUST PANEL REPLACEMENT
Prepare the machine as shown in After Using the
Machine paragraph.
Drive the machine on a level ground.
Remove two mounting screws (1, Fig. Z), then remove
the fastening plate (2).
Remove the dust panel (3, Fig. Z) and replace it.
Perform steps 2 and 3 in the reverse order.
SKIRT DUST PANEL REPLACEMENT
Prepare the machine as shown in After Using the
Machine paragraph.
Start the engine as shown in the relevant paragraph.
Turn the engine throttle lever (19, Fig. B - 29, Fig. C) to
“MAX”.
Lift the hopper (2, Fig. F) by pushing and holding the
right distributor lever (12, Fig. B - 31, Fig. C).
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Install the support rods (4, Fig. F).
Open the skirt (19, Fig. F) by pushing and holding the left
distributor lever (1, Fig. B-C).
Remove six mounting screws (1, Fig. AA).
Remove the dust panel fastening plate (2, Fig. AA) and
the skirt dust panel (3).
Replace the dust panel (3, Fig. AA).
Perform steps 2, 3, 4, 5, 6, 7 and 8 in the reverse order.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.