manualshive.com logo in svg

Nilfisk-Advance Convertamatic 200E 56324004, Operator'S Manual, Page: 16 / 17

Share
Download
Nilfisk-Advance Convertamatic 200E 56324004 Operator'S Manual Download Page 16

 14 - 

Convertamatic 200E 

 Operator Manual  041262

____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

CIRCUIT BREAKERS TRIPPING

Circuit breakers protect electrical circuits and motors from damage due to overload conditions.  If a circuit breaker trips, turn
the Master Key Switch (11) OFF and unplug the machine.  Then try to determine the cause.  Once the problem has been
corrected, reset the circuit breaker by pushing the button in.  If the button does not stay in, wait 5 minutes and try again.
If the circuit breaker trips repeatedly, call your local Advance Dealer for service.

Possible causes for the Brush Motor Circuit Breaker (19) tripping may be:

1

Damaged brush motor (bearings, etc.)

2

Incorrect brush or pad for the application

3

Debris wrapped around brush (or pad) drive pulleys

Possible causes for the Vacuum Motor Circuit Breaker (20) tripping may be:

1

Foam going into vacuum motor (using high-sudsing soap)

2

Recovery Tank Float not closing (drawing water through the vacuum motor)

3

Vacuum motor requires service (carbon brushes, bearings, etc.)

____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

POOR WATER PICKUP

1

Recovery tank full, shut-off float closed

2

Cover not sealing against the top of the tank

3

Plugged vacuum system (inspect squeegee and hoses)

4

Cracked, damaged, or disconnected vacuum hoses

5

Drain plug open

6

Incorrectly adjusted squeegee

____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SQUEEGEE STREAKS

1

Debris under the squeegee blade

2

Worn, nicked or torn squeegee blade

3

Incorrectly adjusted squeegee

____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SWIRL MARKS

1

Running the machine with a dry brush or pad (no cleaning solution)

2

Debris caught in brush or pad

TROUBLESHOOTING

Summary of Contents for Convertamatic 200E 56324004


















Reviews:

No comments