background image

CONCEALING SPEAKER WIRE

 (CONTINUED)

ABOUT EXTERIOR WALLS 

Concealing wires in exterior walls is more complex, since the walls are stuffed with insulation to 
protect the house from the heat and cold outside. Moreover, our national building code requires 
that a horizontal stud placed between the vertical studs break the hollow wall space in exterior 
walls. This “fire blocking” makes it very difficult to retrofit long lengths of wire. In some areas 
of the country, the exterior walls are constructed of solid masonry and have no hollow space for 
speakers or wires. 

PLANNING THE SPEAKER WIRE ROUTE

Start by examining all the possible routes you might take to run the speaker wire from the speaker 
to the home theater system. Use a stud sensor or other device to locate the internal structure of 
the wall. You will want to avoid all studs or joists. 

Figure 10

 shows a typical wire run from the 

speaker location in the ceiling, across the attic, then down through a top plate (i.e., the horizontal 
2-by-4 or 2-by-6 inch wood laid across the vertical studs) to a wall plate or a J-Box in the wall 
behind the home theater system itself.

Find all the locations of your 
existing electrical, phone, and 
TV wiring, and then plan the 
speaker wire route to avoid 
them. Crossing wire paths is  
acceptable, but 60 Hz hum may 
be induced in the reproduced 
audio, if speaker wire is run parallel to electrical wire for more than a few feet. If possible, try to 
keep speaker wire away from parallel power cables by at least 3 feet. 

To find exactly where an electrical cable is routed, try inspecting the inside of the wall by turn-
ing off the breaker for a particular power outlet or switch, removing the cover plate and switch or 
receptacle, and then shining a penlight into the wall. If you have access to an attic or basement 
space, you can quickly see which part of the wall space is free of obstructions, as shown in 

Figure 11

.

Figure 10.

 Running 

speaker wire from a ceiling 
speaker to a home theater 
system location.

Speaker 

Location

Volume 

Control 

Location

Stereo 

Location

12

Summary of Contents for CM6HDFX

























Reviews: