background image

Installation of a panel antenna as an outdoor antenna

Installation of Yagi wide band antenna as an outdoor antenna

Installation of a Yaggi antenna as an outdoor antenna

Cable layout and connector assembly

1. Keep the type, specifications, routing direction, location and curvature radius of cables in compliance with

the model requirements. Place cables in correct order, bend them smoothly, and protect the surface from any

damage.

2. Place RF cables separately from power cables. Take proper isolation measures if they have to be placed on

the same cable racks owing to the site condition restrictions.

3. Fasten all connection parts of the whole system in correct order, from the antenna to repeater interfaces, and

make sure that the electrical interfaces are well contacted. Give waterproof treatment to outdoor connection

parts.

4. Take lightning protection measures for the antenna and feeder system in accordance with the system

requirements. Avoid deforming the antenna feeder where grounding clips are placed, and give waterproof
treatment to the feeder.

Indoor antenna installation

Correct antennas types shall be used according to the site conditions and the requirement.

Summary of Contents for NS-550GDW























Reviews: