Nikrans BD-400FG Installation Manual Download | Manualshive

Page: 15 / 23

background image

Repeater Settings

Indicator Light Instructions

BS

- Outdoor port for connecting an external antenna.

MS

- Indoor ports for connecting an internal antenna.

DC 6V-9V

: for connecting a power supply.

Note:

You can use more than 1 indoor antenna (up to 3) if the covered area has several floors or many walls and partitions. To

connect additional antennas you will need a signal splitter.

Additional accessories selection.

Choosing additional accessories for your signal booster, you should pay attention to the two characteristics: frequency and
impedance. All accessories shall support the device frequencies (refer to specs.)

LCD screen indicators.

1. Introduction screen which is displayed for a few seconds during the system loading.

«
...
13
14
15
16
17
...
»

Summary of Contents for BD-400FG
























Reviews:

No comments

Related manuals for BD-400FG

Brand: Hamilton Beach Pages: 28

Brand: OBH Nordica Pages: 68

AC-CXWP-KVM-KIT

Brand: AVProEdge Pages: 20

Brand: Kalorik Pages: 24

Brand: FRAM Pages: 29

Brand: IOGear Pages: 24

Matrixline 2000 Series

Brand: KVM-TEC Pages: 55

VisionXS-IP-F-DP-HR

Brand: G&D Pages: 248

Brand: Telran communications Pages: 3

Brand: ATEN Pages: 29

Brand: Altronix Pages: 16

Brand: Costar Pages: 33

Brand: KYOWA Pages: 3

Pro Digital 500452

Brand: MuxLab Pages: 12

Brand: FONESTAR Pages: 2

Brand: D-Link Pages: 88

Brand: D-Link Pages: 77

Brand: gofanco Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands