Nikon NPL-632 Instruction Manual Download Page 174 | Manualshive

Page: 174 / 206

background image

7

Specifications

160

Field Station NPL-632 Instruction Manual

CompactFlash card

USB Connecters

Note –

The instrument complies with USB version 1.1.

Note –

Depending on the USB memory model, it may take longer (30 seconds or

more) for the instrument to recognize the USB memory. After you have inserted the
USB memory stick into the slot, Nikon recommends that you wait a while before you
start importing or exporting data from/to the memory stick.

Note –

Some USB memory sticks may not respond to the instrument properly. Nikon

recommends that you use the performance-confirmed models. Please consult your
dealer for details.

Standard Components

•

NPL-632 main body

•

Battery pack BC-80

•

Universal charger and its input code and adapters

•

CompactFlash card (128 MB)

•

Tool set

•

Objective lens cap

•

Vinyl cover

CompactFlash card slot

Type I / Type II x 1

USB connector for PC

1

USB memory stick connector

1

USB B-connector

(ActiveSync technology)

USB A-connector

(for USB memory)

«
...
172
173
174
175
176
...
»

Summary of Contents for NPL-632















































































































































































































Reviews:

No comments

Related manuals for NPL-632

Endura AZ20 series

Brand: ABB Pages: 8

Brand: A&D Pages: 74

Brand: Keithley Pages: 201

HYDROMETTE BL Compact TF-IR 2

Brand: GANN Pages: 40

Brand: Gamry Pages: 16

Brand: Roland Pages: 15

Brand: WAGO Pages: 96

Brand: OBDPROG Pages: 8

Dusty Harp Pickup Series

Brand: Dusty Strings Pages: 5

Brand: Cecomp Pages: 4

Brand: Magnescale Pages: 2

Brand: Datakom Pages: 27

Brand: Extech Instruments Pages: 8

SensoDirect Con200

Brand: Lovibond Pages: 24

Brand: TESTO Pages: 61

Brand: R&S Pages: 43

SAFEMASTER S UH 5947

Brand: DOLD Pages: 60

Brand: Z-Wave Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands