Nikon NPL-302 Series Instruction Manual Download

Page: 78 / 234

Getting Started

Pulse Laser Station NPL-302 Series Instruction Manual

Jobs created before version 1.10

The current database version is 1.10. Jobs
prefixed with ? were created in earlier versions of
the database, and cannot be used in version 1.10.

If a job is from an earlier version, you cannot open
it, set it as the control job, or display its job
information. However, you can use the

DEL

softkey to delete it.

Measuring Distances

3.1

Sighting a prism reflector

31.1

Warning –

Never look at the sun through the telescope. If you do, you may

damage or lose your eyesight.

Sight the telescope to see crosshairs at the center of the
prism reflector.

Jobs created in version 1.02 or earlier are not compatible with version 1.10 or later.
Download all jobs before you update the software that is running on the instrument.

For information on how to assemble the prism reflector, see Setting Up the Prism
Reflector, page 22.

Sighting a single prism

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands