Nikon NPL-302 Series Instruction Manual Download

Page: 42 / 234

Preparation

Pulse Laser Station NPL-302 Series Instruction Manual

Setting Up the Prism Reflector

2.3

The prism reflector is also for measurements in Prism mode.

Assemble the prism reflector as shown in Figure 2.4.

Figure 2.4

Assembling the prism reflector

Adjust the height of the tribrach adaptor (see page 23).

If necessary, change the direction of the prism (see page 23).

Set the prism constant (see page 23).

Set the position of the target plate (see page 24).

Detailed instructions for Step 2 through Step 5 are provided on the following pages.

Target plate for single prism

Tiltable single
prism holder

Tribrach adapter 13/14

Leveling base W10/W11

Tripod

Prism C

Target plate for single prism

Prism C

Tribrach adapter 13/14

Leveling base

Tripod

Tiltable single
prism holder

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands