Nikon NPL-302 Series Instruction Manual Download

Page: 103 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Using

[DSP]

to switch between display screens

Press

[DSP]

to switch between the Stakeout display screens. The following screens

are available:

The S-O8 screen is only available if the secondary distance unit is set. For more
information, see Others settings, page 140.

Every time you press

[DSP]

, the next screen appears. If you press

[DSP]

in the last

screen (S-O7, or S-O8 if the secondary distance unit is set), the S-O1 screen
appears.

To customize the S-O2, S-O3, and S-O4 screens, hold down

[DSP]

for one second.

For more information, see Customizing items in the Basic Measurement Screen
(BMS), page 40.

To record the stakeout point, press

[ENT]

. PT

defaults to the last recorded PT+1.

Press

[ENT]

to record the point.

After recording the point, it returns to the
observation screen. You can continue observation,
or press

[ESC]

to input another angle and distance

for stakeout.

S-O1

S-O2

S-O3

S-O4

dHA

←

OUT

↑

CUT

↑

HA
VA
SD

HA
VD
HD

HL
V%
HD

S-O5

S-O6

S-O7

S-O8

X
Y
Z

dX
dY
dZ

rSD
rVD
rHD

HD
VD
SD

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands