■
LOW BATTERY LEVEL
If battery voltage drops below a certain level, the Status LED will blink Red. As
voltage continues to drop the adapter will turn OFF automatically in order to protect
the Lithium Polymer Battery.
※
Since the adapter enters SLEEP mode when not active, to determine if Battery is
low, turn the adapter back ON and check the Status LED. If the LED blinks when
the Send Button has not been pressed, the power level is low.
Some PC Bluetooth interfaces will display battery status for connected devices. The
adapter transmits the status when connection is completed, and does not updated
afterward. Please use this value as an indication of battery level.
■
CHARGING
・
Disconnect the Communication Cable from the adapter's Micro-USB Connector, and connect the Charging Cable.
・
Connect the USB-A end of the cable to the AC-USB Charger, or to a PC Port for charging
※
The charging LED will light when charging is started. The LED will go out when complete.
■
AFTER USE CARE
・
STORAGE
Storage
When not in use, store away from direct sunlight in moderate temperatures (0°C~40°C).
Store with the power OFF. If not used for a long period, please maintain the battery by charging to
50% capacity every three months.
■
TROUBLESHOOTING
Problem
Cause
Solution
Will not Pair
①
A USB Bluetooth adapter is not
plugged in.
②
The settings on the PC and the
Wireless adapter may not match.
①
Please install a USB Bluetooth adapter compatible
with BluetoothLE (HOGP profile) into the Wireless Adapter.
②
Delete the device "BLEBOX" in the PC's Bluetooth device
list, reboot the PC, and try again.
Device
not found
①
Pairing Mode did complete.
②
The settings on the PC and
the Wireless adapter may
not match.
①
Make sure a USB Bluetooth adapter is plugged in.
Hold down the Send Button and press the Power Button
at same time to enter pairing mode.
②
Please try the following.
・
Delete the device "BLEBOX" in the PC's Bluetooth device list.
・
Remove and replace the PC Bluetooth adapter.
・
Reboot the PC
Data does
not transmit
①
Measuring instrument data
does not display.
②
Bluetooth connection error.
③
Software communication
error.
④
Bluetooth status error.
⑤
Display reads "ERR1"
⑥
Once power is turned OFF,
does not reconnect when
power is turned back ON.
①
Check the measuring instrument and cable, and make
sure the instrument is in a measuring mode.
②
Make sure the device is within Bluetooth range, and redo
the pairing if necessary.
③
Close, and then restart the communication software.
④
Cancel the pairing, remove and reinsert the PC Bluetooth
adapter, and pair again.
⑤
No data is received by adapter, so there is a problem with
the measuring instrument or communication cable, please
check..
⑥
If you turn OFF power, and turn ON again before
the PC disconnects, the PC will not connect to
the device. Please remove and reinsert the PC
Bluetooth adapter, reboot, and pair again.
■
COMMUNICATION DATA SPECIFICATION
When Send Button is pressed, the following information is transmitted using HID class protocol. After sending,
the device enters sleep state.
When sleep state is entered after transmitting data, it will only be canceled when Send Button is Pressed again.
Normal operation (Ex. data = "−1.23")
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2D
30
30
31
3E
32
33
20
20
20
0D
0A
FF
FF
FF
FF
FF
FF
00
-
0
0
1
.
2
3
CR
LF
(address unique for each adapter)
For Error Event (Error Code = 1 Measuring Instrument not connected)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
E
R
R
1
CR
LF
(address unique for each adapter)
■
SPECIFICATION
Model
: DTW-DG01
Wireless Protocol : Bluetooth LE (HOGP profile compatible)
Input
: Caliper proprietary signal
Output
: USBHID class compliant
Power
: Lithium Polymer Battery (350mAh)
Continuous on time: 17 hours (for send rate of 250 sends/hr)
charge time
: 100 minutes
Dimensions
: 35(L)×57(W)×17.5(H)mm
Weight
: 45g (Including battery)
Package contents : Main unit (×1), B-LOG software (×1), Charging Cable(1m) (×1),
Communication Cable (20cm, ×1), Mounting Bracket (×1),
Plate Screw (M3, ×1), Caliper Mounting Screw (M2, ×1),
Washer (×1), Instruction Manual
Compatible OS
: Windows7, 8.1, 10, Android, iOS
■
NOTES
For best performance, and in order to keep the adapter in good condition for long service, please read and follow
these instructions.
●
Avoid using where the device will be subject to the following conditions:
・
Dirty or dusty locations
・
Exposed to direct sunlight
・
Exposed to acids, alkali solutions, or organic solvents.
・
Exposed to oils or water.
・
Equipment which creates sparks or electric discharge, or other locations which require high electric shielding.
・
Near equipment which produces strong electromagnetic fields, such as high voltage cables, or broadcasting
facilities.
●
Clean only with dry cloth slightly moistened with a mild detergent or alcohol. Do not use any organic solvents.
●
Do not disassemble or modify.
N
IIGATA SEIKI CO., LTD
6-15-22, Tsukanome, Sanjo-city, Niigata Pref. 955-0055 JAPAN
TEL: 0256-31-5660 FAX: 0256-39-7730
URL http://www.niigataseiki.co.jp
