Nidec-Shimpo FGS-220VC Operation Manual Download | Manualshive

Page: 5 / 36

background image

Attention Safety

Warning

Disconnect from the AC outlet during any maintenance of the stand. Also, unplug when not

using for long periods of time.

May cause electric shock, a fire and injury.

Attention before using FGS-VC

Avoid the following.

Place where water, oil, or medicine may splash

Dusty locations
Places where condensation occurs

Places where explosive gases or ignition sources

are present.
Place where high vibration may occur

Places outside of operating temperature range.
32-104°F (0-40°C)

Cleaning with thinner and gasoline, etc.

Make sure the cable is not stuck in the stand.

Install the force gauge after turning off the power

switch.

Adjust the limit switches when the motor stops.

When digital force gauge FGV series is installed

Set "ovEr" in the F06 parameter, which is the parameter of Output Type.
If "ovEr" is not set, FGS-VC does not stop by the overload of the force gauge.

Confirm that the power supply is the
same voltage rating as the displayed
voltage rating on the unit

Do not plug AC connector with wet hand.

There is the possibility of elect ric shock.

All manuals and user guides at all-guides.com

«
...
3
4
5
6
7
...
»

Summary of Contents for FGS-220VC





































Reviews:

No comments

Related manuals for FGS-220VC

Brand: Fantek Pages: 32

Brand: La Siesta Pages: 6

Brand: VMP Pages: 3

Brand: ricoo Pages: 12

Brand: L-Acoustics Pages: 4

Brand: Sim-Lab Pages: 10

Brand: LA VAGUE Pages: 38

Brand: Datavideo Pages: 20

Levitouch DM-552

Brand: GABOR Pages: 16

Allen-Bradley 2198-K5700-MOUNTKIT

Brand: Rockwell Automation Pages: 12

Brand: WE-EF Pages: 7

HQ Power HQSS11002

Brand: Velleman Pages: 13

Brand: Ovation Pages: 3

RAPIDDOC PRO KIOSK

Brand: MTI Pages: 11

Brand: Sanus Pages: 2

Neomounts FPMA-C020BLACK

Brand: NewStar Pages: 8

Brand: IBEX Pages: 2

Brand: Rousseau Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands