background image

NICOR, Inc.   2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393   www.nicorlighting.com  July 26, 2021 10:46 AM

ECL3 

Slim LED Combo Exit Sign & Emergency Light

INSTALLATION INSTRUCTIONS

Model: ECL310UNVWHG2SD, ECL310UNVWHG2RSD, 

ECL310UNVWHR2SD, ECL310UNVWHR2RSD

GENERAL PRODUCT WARRANTY. Each NICOR product will be free from defect in materials and workmanship for a period of one (1) year from the date of delivery to the end-user. Powder Coat paint finish on products, other 
than natural aluminum or brass, will not exhibit cracking, peeling, excessive fading, or corrosion during the warranty period. Exceptions apply as defined in each NICOR product’s specification sheets, which are incorporated 
by reference herein. Warranty does not cover improper installation, operation, alterations, power surges, overheating due to external conditions, or acts of nature including but not limited to lightning strikes.

ALL NICOR WARRANTIES APPLY ONLY TO NICOR PRODUCTS THAT HAVE BEEN PURCHASED FROM AN AUTHORIZED NICOR DISTRIBUTOR; WHO PURCHASED THE PRODUCT DIRECTLY FROM NICOR; THE PRODUCT WAS NEW 
AND IN AN UNOPENED NICOR PACKAGE AT THE TIME OF INSTALLATION; AND WAS INSTALLED BY A LICENSED ELECTRICIAN OR UNDER THE SUPERVISION OF A LICENSED ELECTRICIAN.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ-
ing interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help

NOTE

Battery Testing: Allow 24 hours of charging before testing.
•  Push In TEST Button - Fixture will switch to battery power and remain lit 
•  Release TEST Button - Fixture will switch back to AC power

4

6

Operating status:

When AC power is supplied to the fixture, the unit will automatically initiate a self-test and self-diagnostic test as 

follows: 

1. Verifies battery disconnection, charger board failure, lamp failure and transformer failure every 5 seconds.
2. One minute self test every month 
3. 30 minute self test on the 6th month of the year after installation
4. 90 minutes self test on the 12th month of the year after installation
Note: All functions are pre-set at the factory and do not require field adjustment. 

For manual test, press test button as follows:

5

Indicator light status: 

Indicator is a dual color LED that shows the following status: 

Green

1. Solid On : Ready
2. Blinking : Testing

Red - Service Alert

One blink ON/pause every 4 seconds

Battery is not connected

Two blinks ON/pause every 4 seconds

Battery voltage drops below acceptable value

Three blinks ON/pause every 4 seconds

Charger board fault

Four blinks ON/pause every 4 seconds

Transformer 

function failure

Five blinks ON/pause every 4 seconds

Emergency lamp fault

Six blinks ON/pause every 4 seconds

Remote head lamp fault

Seven blinks ON/pause every 4 seconds

LED strip fault (Exit Sign)

Press test button once 

1 minute test

Press test button 2x (within 2 seconds)

5 minute test

Press test button 3x (within 2 seconds)

30 minute test

Press test button 4x (within 2 seconds)

90 minute test

Reviews: